User manual PIONEER VSX-C100

[. . . ] AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-C100 Operating Instructions Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. In some countries or regions, the shape of the power plug may sometimes differ from that shown in the explanatory drawings. [. . . ] Optical connection default settings You can connect your digital video components (like a DVD player, satellite tuner, or DVR) with optical or coaxial cords, as explained directly above and on page 11. However, the optical terminals cannot be assigned, you must follow their default settings in order to match your equipment to the remote control buttons (and display names, etc. ) of this receiver. Thus if you followed the default setting for the coaxial terminal and hooked a DVD up to that terminal the optical terminal default settings are: OPT. 2: DVR If you assigned your TV/SAT (displayed as SAT) to the coaxial terminal (see "Coaxial connection setting" above and "Connecting Your Equipment" page 12­14) then the defaults for the optical terminals will change (because you cannot have one component assigned to two different places). 2: DVR English Follow steps 1&2 on page 27 (if necessary). Use the +/­ buttons to set the input attenuator ON or OFF . Press SETUP to advance to the next receiver setting mode. Press ENTER if you want to exit the setting mode. · The default setting is "OFF". · When the OVER indicator light please put the input attenuator ON. · The Input Attenuator is expressed as IN. ATT in the display. Coaxial connection setting (assigning the coaxial terminal) This receiver has two different ways you can connect your digital video components (like a DVD player, satellite tuner, or DVR). You can connect them with an optical or coaxial cords (see p. 11). The easiest way to hook your equipment is using the default settings of this receiver. In this case, use a coaxial cord to connect your DVD player. If you use the coaxial terminal for your satellite or TV tuner (called TV/SAT on the receiver) you need to assign that component to the remote (that is, tell the remote that you used the coaxial terminal for your TV/SAT). The optical terminals' default settings will change in accordance with how you assign the coaxial terminal here. See the next heading for more information. Follow the default settings when hooking up equipment to the optical terminals. Follow steps 1&2 on page 27 (if necessary). Use the +/­ buttons to choose the component that you hooked up with coaxial cords. Press SETUP to advance to the next receiver setting mode. Press ENTER if you want to exit the setting mode. 31 En Fine Tuning Your Surround Sound Setting the Volume Level of Each Channel (adjusting the speaker volume balance) Use to set the relative volume of each channel as you find necessary. 4 Use the + or ­ buttons to adjust speaker levels so that you hear the test tone at the same volume from each speaker when seated in your main listening position. · If a speaker is deselected in the center, surround speaker or subwoofer setting mode (see page 28) then no test tone will be output for that speaker. · The channel level range is ± 10 dB. · Levels can be set for each surround mode. 1 4 (+/- button) RECEIVER SIGNAL SELECT SOURCE 5 Press TEST TONE to turn off the test tone. SLEEP DVD TV / SAT FRONT DIMMER DVR/ VCR FM / AM SURROUND ADVANCED SOUND MODE AUTO 3, 5 CH SELECT button ROOM SETUP TEST TONE CH_SELECT SETUP ENTER MUTE MASTER VOLUME TOP MENU DISPLAY TUNE T. EDIT MENU 2 P ST ST MENU ENTER AUDIO TUNE SUBTITLE EON RF ATT GUIDE A P EXIT SEARCH E CLASS C MPX D D. ACCESS E ENTER 10 TV CONTROL CHANNEL INPUT SELECT · Since the subwoofer transmits an ultra-low frequency its sound may seem quieter than it actually is. Be careful not to turn up your subwoofer too much and check the volume with an actual source. · The subwoofer volume is best controlled with the volume control on the powered subwoofer. · The speaker volume can be adjusted without outputting the test tone by pressing CH SELECT and +/- button. · The default setting is 0 dB for all channels. · If you have adjusted the channel level using the + button, even if the master volume is all the way up you'll never actually get a volume level that is 0 dB (full volume). CHANNEL VOLUME RECEIVER 1 Press RECEIVER to turn the power on. 2 Press MASTER VOLUME + or ­ to adjust the volume to an appropriate level. [. . . ] Loop antenna Miscellaneous Power Requirements UK model . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 220 ­ 230 V, 50/60 Hz European model . . . . . . . . . . . . . . . . . AC 220 ­ 230 V, 50/60 Hz Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 W In Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]