User manual PIONEER VSX-D510

[. . . ] AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-D510 Operating Instructions WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THE STANDBY/ON BUTTON IS SECONDARY CONNECTED AND THEREFORE DOES NOT SEPARATE THE UNIT FROM MAINS POWER IN STANDBY POSITION. IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] 3 NUMBER/MODE buttons (see pages 26, 31, 32) Use the number buttons to select the radio frequency in tuner DIRECT ACCESS mode or the tracks in CD, DVD mode etc. Also, buttons marked with the following names have special functions. If you try to use one of these functions but the display flashes it means that function cannot be used in the current mode (for example DSP modes cannot be used when 5. 1 CH setting is on). 2 (see pages 17, 25) Use to put receiver in DOLBY DIGITAL, DOLBY SURROUND and DTS modes. To use first press the RECEIVER button then operate this button. DSP mode (see pages 24) Use to put receiver in one of the DSP modes. To use first press the RECEIVER button then operate this button. MIDNIGHT (see page 24) Use to put receiver in MIDNIGHT mode. To use first press the RECEIVER button then operate this button. 5. 1 ch (see page 24) When the DVD/LD or DVD 5. 1 CH function is selected each press switches the DVD/LD input between DVD/LD and DVD 5. 1 CH. To use first press the RECEIVER button then operate this button. CHANNEL SELECT (see page 17-memo) Use to select a speaker when setting up the surround sound of the receiver. To use first press the RECEIVER button then operate this button. TEST TONE (see page 17) Use to sound the TEST TONE when setting up the surround sound of the receiver. To use first press the RECEIVER button then operate this button. ATT If the Overload indicator lights often, use to attenuate (lower) the level of an analog input signal to prevent distortion. To use, press the RECEIVER button first, then press this button. CHANNEL LEVEL +/­ (see page 17-memo) Use to set up the levels of the surround sound of the receiver. To use first press the RECEIVER button then operate this button. SIGNAL SELECT (see page 23) Use to select the proper signal (analog, digital) for the source your are inputting. To use first press the RECEIVER button then operate this button. 4 THE FOLLOWING FOUR SETS OF BUTTONS ARE DEDICATED TV CONTROL. THEY ARE ONLY USED FOR CONTROLLING YOUR TV. [. . . ] 1 Vp-p/75 Frequency Response VCR/DVR, DVD/LD, TV/SAT MONITOR +0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hz to 7 MHz ­3 dB Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB Cross Talk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB NOTE: · Specifications and the design are subject to possible modifications without notice, due to improvements. * Measured pursuant to the Federal Trade Commission's Trade Regulation rule on Power Output Claims for Amplifiers. [. . . ]