User manual PIONEER VSX-D909S

[. . . ] AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-D909S Operating Instructions Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [For U. S. model] IMPORTANT NOTICE The serial number for this equipment is located on the rear panel. [. . . ] If starting fresh, complete steps 1-3 in "Setting Up for Surround Sound" (p. 29) first. Î S0URCE MULTI OPERATION USE SETUP RECEIVER SYSTEM OFF DVD/LD TV/SAT VCR1 VCR2 MULTI CONTROL CD CLASS MD/ TAPE1 MPX TUNER BAND TVCONT DIRECT ACCESS 1 Select BASS PEAK LEVEL (if continuing from CROSSOVER NETWORK it will already be selected). See "Setting Up for Surround Sound" on page 29 if you are unsure how to do this. Press the ENTER button. Bass Peak Level Manager 7 ¶ - TUNING + 1 ¡ DTV ON/OFF DTV MENU 3 8 - STATION + 4 ¢ CHANNEL + - 1 4 7 GUIDE +10 2 5 8 0 3 6 9 EXIT ENTER DISC [Setting Start ] [Setting Cancel] [EXIT] + TV VOL TV TV CONTROL TV FUNC + VOLUME ­ REMOTE SETUP INPUT ATT SYSTEM SETUP EFFECT/ CH SEL ­ MUTE FUNCTION MENU + ENTER 1-3 SIGNAL SELECT DSP STEREO/ DIRECT DIGITAL NR ­ MULTI CH INPUT MIDNIGHT /DTS LIGHT ADVANCED STANDARD 2 Output the test tone for the LFE channel and specify the peak level. 1 If your subwoofer has a volume control, set it to the middle position before proceeding. 3 Press the ENTER button. Bass Peak Manager [Setting OK ] AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT Bass Peak Level [­ 50] [EXIT] AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-D909S Digital Signal Processor STANDBY/ON STANDBY DSP MODE STEREO/ DIRECT MULTI-ROOM &SOURCE INPUT SELECTOR /DTS SIGNAL SELECT ADVANCED STANDARD CONTROL MASTER VOLUME MASTER VOLUME rotates to MIN (---dB). Then the test tone is output to the subwoofer or front or surround speakers. 4 Use the 2 or 3 button arrows to gradually increase the level of the LFE channel until the test tone begins to distort. Then go back and leave the level setting at a point just before that. Press the ENTER button and the receiver will remember this bass output level. To exit before outputting the TEST TONE select EXIT and press the ENTER button. To exit while outputting the TEST TONE press the ENTER button. S-VIDEO PHONES VIDEO INPUT L AUDIO R VIDEO MULTI CH INPUT TONE CHANNEL SELECT LOUDNESS DIGITAL NR FL DIMMER CLASS BAND - TUNING + SPEAKERS - BASS + - TREBLE + VIDEO SELCT TAPE 2 MONITOR MPX TUNER CONTROL - STATION + MEMORY DOWN UP MASTER VOLUME memo If you select SETTING CANCEL no settings are input to the receiver but the screen remains on the TV. To escape the screen you must Select EXIT and press the ENTER button. 3 Select EXIT and press the ENTER button to return to the SYSTEM SETUP MENU. This completes the speaker setup. 38 Initial Set Up Dynamic Range Control This feature makes it possible to enjoy full surround sound effects on Dolby Digital sources even at low volumes. It does this by compressing the dynamic range. Dynamic range is the difference between the loudest and the softest sounds in any given signal. Compressing the range plays sounds so the quieter ones are audible and the louder ones don't get distorted or become overpowering. This feature only applies to Dolby Digital sources but the MIDNIGHT LISTENING mode accomplishes the same end for a variety of sources (see page 49). If continuing from Bass Peak Level go to step 1. If starting fresh, complete steps 1-3 in "Setting Up for Surround Sound" (p. 29) first. Î S0URCE MULTI OPERATION SYSTEM OFF USE SETUP RECEIVER DVD/LD TV/SAT VCR1 VCR2 MULTI CONTROL CD CLASS MD/ TAPE1 MPX TUNER BAND TVCONT DIRECT ACCESS 1 Select D-RANGE CONTROL (if continuing from BASS PEAK LEVEL, it will already be selected). See "Setting Up for Surround Sound" on page 29 if you are unsure how to do this. Press the ENTER button. Dynamic Range Control 7 ¶ - TUNING + 1 ¡ DTV ON/OFF DTV MENU 3 8 - STATION + 4 ¢ - CHANNEL + 1 4 7 GUIDE +10 2 5 8 0 3 6 9 EXIT ENTER DISC Select Mode [OFF] (For Dolby Digital) + TV VOL TV TV CONTROL TV FUNC + VOLUME SET UP [EXIT] ­ REMOTE SETUP INPUT ATT SYSTEM SETUP EFFECT/ CH SEL ­ MUTE FUNCTION MENU + ENTER 1-3 SIGNAL SELECT DSP STEREO/ DIRECT · The default setting is OFF. · If listening at loud volumes we recommend turning the Dynamic Range Control OFF. DIGITAL NR ­ MULTI CH INPUT MIDNIGHT /DTS LIGHT ADVANCED STANDARD 2 Use the 2 or 3 arrows to choose OFF, MID or MAX. 3 Select EXIT and press ENTER button to return to the SYSTEM SETUP MENU. If you want to change a setting before proceeding choose a new DYNAMIC RANGE CONTROL setting. You may need to experiment with different Dolby Digital sources before you can use the DYNAMIC RANGE CONTROL setting to suit your low volume listening needs. AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT 39 Initial Set Up Multi Channel In Setting If you have a Multi Channel external decoder you can choose whether to have the sound level set to BYPASS, in which case only the main volume can be controlled, or to ADJUST, which means the levels can be reduced in volume. If continuing from Dynamic Range Control go to step 1. If starting fresh, complete steps 1-3 in "Setting Up for Surround Sound" (p. 29) first. Î S0URCE MULTI OPERATION USE SETUP RECEIVER SYSTEM OFF 1 Use the 5¥ buttons to select MULTI CHANNEL IN. See "Setting Up for Surround Sound" on page 29 if you need more information. [. . . ] Total 100 W (0. 8 A) MAX UNSWITCHED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 W (0. 8 A) MAX Dimensions . . . . . . . . . . . . . . . . . . 420 (W) × 173 (H) × 470 (D) mm (16-9/16 (W) × 6-13/16 (H) × 18-1/2 (D) in. ) Weight (without package) . . . . . . . . . . . . . . . 14. 4 kg (31 lb 13 oz) * Measured pursuant to the Federal Trade Commission's Trade Regulation rule on Power Output Claims for Amplifiers. [. . . ]