User manual PIONEER VSX-LX53

[. . . ] Operating Instructions VSX-LX53 audio/video multi-channel receiver VSX-2020-K IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D3-4-2-1-1_A1_En Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. IMPORTANT: THE MOULDED PLUG This appliance is supplied with a moulded three pin mains plug for your safety and convenience. [. . . ] The HDMI OUT1 terminal is compatible with the Control with HDMI function. · Press RECEIVER , then press HDMI OUT. Please wait a while when Please wait . . . The output switches among HDMI OUT ALL, HDMI OUT 1 and HDMI OUT 2 each time the button is pressed. 1 Checking your system settings Use the status display screen to check your current settings for features such as surround back channel processing and your current MCACC preset. 1 Press RECEIVER , then press STATUS to check the system settings. The front panel display shows each of the following settings for three seconds each: Input function, Sampling Frequency, MCACC preset, ZONE 2 input, ZONE 3 input and HDMI OUT. 2 When you're finished, press STATUS again to switch off the display. Using the Web Control function The receiver can be operated using a browser from a computer connected on the same LAN as the receiver. 1 Turn on the computer and launch the Internet browser. 2 In the address bar on the browser, enter the IP address assigned to this receiver. For example, if the IP address of this receiver is "192. 168. 0. 2", enter "http://192. 168. 0. 2/". When the connection is made with the receiver, a Top Menu will be displayed. This receiver's IP address can be found in the `IP address, Proxy' menu (page 80). 3 Once the Top Menu is displayed, click the button for the zone you want to operate. 4 Operate from the screen for the individual zone. · Even when the receiver is in the standby mode, it can be turned on using the Web Control function. For details, see Network Standby on page 81. Top Menu Resetting the system Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. · Disconnect the iPod and USB memory device from the receiver beforehand. 1 Switch the receiver into standby. 2 While holding down ENTER on the front panel, press STANDBY/ON. 3 Select `RESET' using PRESET /, then press ENTER on the front panel. OK appears in the display to indicate that the receiver has been reset to the factory default settings. · Note that all settings will be saved, even if the receiver is unplugged. Web Control Main ZONE POWER ON OFF ZONE 2 VOLUME -60. 0dB ZONE 3 MUTE INPUT SELECT DVD LISTENING MODE AUTO SURR/ALC/ STREAM DIRECT STEREO HOME THX STANDARD SURROUND ADVANCED SURROUND STEREO Note 1 · The synchronized amp mode is canceled when the HDMI output is switched. [. . . ] When the microwave is not in use, there will be no radio wave interference. Precautions regarding connections to products supported by AS-BT100 · Complete connections for all devices supported by AS-BT100, including all audio cords and power cables before connecting them to AS-BT100. · After completing connections to AS-BT100, check the audio and power cables to confirm that they not twisted together. · When disconnecting AS-BT100, confirm that you have sufficient working space in the surrounding area. · When changing connections of audio or other cables for products supported by this unit, confirm that you have sufficient working space in the surrounding area. [. . . ]