User manual PIONEER VSX-LX60

[. . . ] Operating Instructions AUDIO/VIDEO MULTI-CHANNEL RECEIVER IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D3-4-2-1-1_En-A Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. IMPORTANT: THE MOULDED PLUG This appliance is supplied with a moulded three pin mains plug for your safety and convenience. [. . . ] 2 The subwoofer is excluded from correction. The super tweeter in the super high-frequency range is excluded from correction. Also, speakers theoretically unaffected by group delay (full-range speakers, for instance) are excluded from correction. Because calibration involves the spatial characteristics, you may not get the same results after you perform calibration again depending on your audiovisual environment and your speaker system. 3 This can be done in Automatically setting up for surround sound (MCACC & Full Band Phase Control) on page 8 or Automatic MCACC (Expert) on page 39, either of which you should have already completed. 48 En The System Setup menu 08 1 Select `MCACC Data Check' from the Data Management setup menu. DVD /L D 5. S pe ak er S et ting Cha nnel Leve l S pe ak er Dist anc e S t anding Wave Ac oust ic Ca l E Q FULL BAND P HAS E CTRL : Ret urn Copying MCACC preset data If you want to manually adjust the Acoustic Calibration EQ (see Manual MCACC setup above), we recommend copying your current settings1 to an unused MCACC preset. Instead of just a flat EQ curve, this will give you a reference point from which to start. 1 Select `MCACC Memory Copy' from the Data Management setup menu. DV D/ L D 5 . MCACC Me mo r y Co py Copy All Data From [ M1. MEMORY 2 ] Start Copy :Re tu rn [Cancel ] :Cancel M C ACC Dat a Ch eck M em o r y Ren am e M C ACC M em o r y Co py M C ACC M em o r y Clear Ou t p u t P C : Ret u r n E NTE R:Next 2 Select the setting you want to check. · It is useful to do this while a source is playing so you can compare the different settings. 3 Select the MCACC preset that you want to check. Use the / buttons if necessary to switch speakers/ settings. - 5 5 . E Q D a t a C h e ck MCACC M1 63Hz : +0. 5 Ch [SBL] 125Hz : -5. 5 dB 250Hz : +3. 0 500Hz : 0. 0 1kHz : +12. 0 2kHz : +5. 5 4kHz : -3. 0 8kHz : 0. 0 16kHz : +7. 0 :Return TRIM : -2. 5 TRIM 63 125 250 500 1k 2k 4k 8k 16k MCACC Da ta Ch e ck Me mo r y Re n a me MCACC Me mo r y Co py MCACC Me mo r y Cl e a r Ou tp u t P C 2 Select the setting you want to copy. · All Data ­ Copies all the settings of the selected MCACC preset memory. · LEVEL & DISTANCE ­ Copies only the channel level and speaker distance settings of the selected MCACC preset memory. 4 Press RETURN to go back to the Data Check menu, repeating steps 2 and 3 to check other settings. 5 When you're finished, press RETURN. You will return to the Data Management setup menu. 3 Select the MCACC preset you'll be copying the settings `From' then specify where you want to copy them (`To'). Make sure you don't overwrite an MCACC preset you're currently using (this can't be undone). 4 Select `Copy' to confirm and copy the settings. Completed shows in the OSD to confirm the MCACC preset has been copied, then you automatically return to the Data Management setup menu. Renaming MCACC presets If you have several different MCACC presets that you're using, you may want to rename them for easier identification. 1 Select `Memory Rename' from the Data Management setup menu. DVD /L D 5. Me mor y Re nam e MCACC Pos ition Re nam e M1 M2 M3 M4 M5 M6 [ [ [ [ [ ME M ORY M E MORY M E MORY M E MORY M E MORY M E MORY 1 2 3 4 5 6 ] ] ] ] ] Clearing MCACC presets If you are no longer using one of the MCACC presets stored in memory, you can choose to clear the calibration settings of that preset. 1 Select `MCACC Memory Clear' from the Data Management setup menu. DV D/ L D 5 . [. . . ] DTS-HD Master Audio delivers audio signals to listeners without any loss of data with its high transfer rates. · Phase Control The Phase Control feature corrects the phase distortion as well as group delay for LFE (Low-Frequency Effects) audio signals during multichannel playback. · Full Band Phase Control The Full Band Phase Control feature analyzes the frequency-phase characteristics of the speakers connected and corrects the phase distortion to the flattened frequency-phase characteristics. This correction minimizes the group delay of the middle- and low-frequency ranges against the high-frequency range and improves the frequency-phase characteristics across all ranges. [. . . ]