User manual PIONEER XR-P370CR SERVICE MANUAL

[. . . ] Secondary Function: Press and hold both switches for 2 seconds to engage the Audio Tone Control mode. See page 6 (Sound Quality or Phase Inversion) for details. [MUTE-A] / [MUTE-B] Switches The [MUTE-A] switch allows you to mute the audio from the VFO-A receiver. Similarly, the [MUTE-B] switch allows you to mute the audio from the VFO-B receiver. This can be particularly useful during Dual Receive operation, when you want to concentrate on just one receiver for a moment. REAR PANEL CONNECTIONS DC IN +13. 8V Jack Connect the supplied DC cable between this jack and +13. 8V jack on the FTDX5000 transceiver. [PGM] Switch This slide switch is used for updating the XR-P370CR firmware. [. . . ] Available selections are: 25 kHz 50 kHz 100 kHz 250 kHz, kHz, kHz, kHz, kHz, kHz, kHz. Rotate the (VFO-A)[SELECT] knob to select the Menu item "ATT then rotate the (VFO-B)[SELECT] knob to select ATT", ATT the display attenuation value according to current propagation conditions, your operating frequency, and antenna, etc. Available selections are: 0 dB 10 dB and 20 dB dB, dB, dB. [C. S] key briefly to save the new setting and 6. Press the exit to normal operation. [C. S] Switch (VFO-A)[SELECT] Knob (VFO-B)[SELECT] Knob OPERATING Mode CTR Current VFO-A Frequency TRACE Mode NOR: Normal AVG: Average PEAK: Peak Hold CHANGING THE TRACE MODE 1. Press and hold the FTDX5000 [C. S] key for 2 seconds to engage the Scope Menu mode. The SUB DISPLAY-I window will show the Group name (SCOPE while the SUB DISPLAY-II window SCOPE), SCOPE will show the Menu item. The SUB DISPLAY-III window shows the setting of the currently-selected Menu item. Rotate the (VFO-A)[ SELECT] knob to select the Menu item "TRACE then rotate the ( VFOTRACE", TRACE )[SELECT] knob to select the desired trace mode. B Available selections are shown at the right. Press the [C. S] key briefly to save the new setting and exit to normal operation. Rotate the (VFO-A)[SELECT] knob to select the LBWS", Menu item "LBWS then rotate the ( VFOLBWS B)[SELECT] knob to select the desired sweep area. Available selections are shown at the right. Press the [C. S] key briefly to save the new setting and exit to normal operation. L: LBWSx L The Spectrum scan sweeps the band segment on the lower side of the operating frequency. LBWSx M The Spectrum scan sweeps the band segment M: centered on the operating frequency. H: LBWSx H The Spectrum scan sweeps the band segment on the upper side of the operating frequency. x: 1, 2, or 3; indicates the sweep segment that is designated in the Menu item "MODE described previously. MODE", MODE The above examples are "2" (LBWS-2 LBWS-2). 2 LBWS-2 -4- USING THE FIX (FIXED) MODE The FIX mode is convenient when you want to monitor an entire amateur band. The starting point, located at the left edge of the screen, can be set for each amateur band via FTDX5000 Menu items ("131 SCP 131 FIX" FIX"). Even if the screen span (bandwidth) is changed, the start frequency will not be changed. By 1. 8 FIX ~ 141 SCP 50. 0 FIX watching the screen, you can move your operation to a clear channel or find frequencies where interesting activity appears on the display. Press and hold the FTDX5000 [C. S] key for 2 seconds to engage the Scope Menu mode. The SUB DISPLAY-I window will show the Group name (SCOPE while the SUB DISPLAY-II window will show SCOPE), SCOPE the Menu item. [. . . ] MILD: The high pitch tones of the receiver audio MILD are reduced, without changing the low base sound quality. SOFT: The low frequency base range of the receiver SOFT audio is boosted and the high pitch tones are reduced. LOUDNESS: LOUDNESS The low frequency base range of the received audio is boosted while preserving clear sound quality, with high readability. The amount of brightness may be set via FTDX5000 Menu item "011 DISP DIM ELCD". -7- SUPPLIED OPTION Mini-DIN Cable (T9101526) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]