User manual PLANAR LA1910RTC Operations Manual

[. . . ] - Near any appliance generating a strong magnetic field. - Place in direct sunlight. 4 Introduction About Planar's LA1910R / LA1910RTC The LA19 is a 19" flat panel screen with an active matrix, thin-film transistor (TFT), liquid crystal display (LCD). Features include: Dual signal input: Analog VGA and Digital DVI-D Active matrix TFT LCD technology 1280 x 1024 SXGA resolution 19" viewable display area 31. 5 ~ 80 kHz horizontal scan 56 ~ 75 Hz refresh rate 0. 294mm x 0. 294mm pixel pitch 250 cd/m2(typ. ) brightness 500:1(typ. ) contrast ratio L/R=85º/85º, U/D=85º/85º viewing angle, CR=10 Tr=15ms(typ. )/Tf=10ms(typ. ) response time CCFL backlight lamps w/30, 000 hrs life Auto-adjustment function Multilingual OSD user controls VESA DPMS power saving Durable, capacitive touch screen ( for LA1910RTC) 5 Touch Screen (for LA1910RTC) Capacitive for finger interface Optical Clarity: Up to 88% light transmission Touch Contact Requirement: 3 ms for finger input Surface Scratch Hardness: Cannot be scratched using any stylus with Mohs' rating of less than 6. 5. Durability: Touch screen has been tested in a laboratory environment to withstand over 225 million mechanical touches without noticeable degradation to the surface Surface Obstructions: Touch screen's operation unaffected by surface obstructions such as dirt, dust, grease, smoke, etc. Chemical Resistance: Touch screen is highly resistant to corrosives, in accordance with ASTM-D-1308-87 (1993) and ASTMD-F-1598-95. [. . . ] Horizontal Position Changes the horizontal position of the image. Vertical Position Changes the vertical position of the image. Frequency Changes the display data frequency to match the frequency of the graphic card. When a vertical flickering bar is seen, use this function to make an adjustment. Tracking Synchronizes the signal timing of the display with the graphic card. When you are experiencing unstable to flickering image, use this function to make an adjustment. 14 On-Screen Display Menus Second OSD Menu: Display Mode Selects this function to view the display resolution, vertical refresh, and horizontal scan of the current mode. OSD Off-Time Adjusts the time it takes for the OSD menu to disappear. Text-Graphic Toggles between VGA text mode (mode M03H) and graphic mode (mode M13H). Sharpness Adjust the sharpness of the image. Reset Returns the display parameters of the current mode to the factory default settings. 15 On-Screen Display Menus Third OSD Menu: Volume Controls the sound volume. Video Source Changes the video mode between multiple connections. 16 On-Screen Display Menus Fourth OSD Menu: Color Adjusts the color temperature. Color Adjustment-Red Adjusts the red color of the display. Color Adjustment-Green Adjusts the green color of the display. Color Adjustment-Blue Adjusts the blue color of the display. 17 Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or visit Planar Support at www. planar. com/support. See support contact information on rear cover. Check that all the I/O and power connectors are installed correctly and well connected as described in the "Installation" section. Make sure the pins of the connectors are not crooked or broken. Problem: Partial image or incorrectly displayed image. Check to see if the resolution of your computer is higher than that of the LCD display. Reconfigure the resolution of your computer to make it less than or equal to 1280 x 1024. Problem: Image has flickering vertical line bars. [. . . ] If the touch screen driver does not automatically load, restart the system. Touch Panel Setting and Calibration: 1. Open the "Control Panel" of the system. Double click the "Touch Panel" icon. Select the item you want to set up and change the setting values. [. . . ]