User manual PLANAR PDP60B PRODUCT MANUAL

[. . . ] Manual PLANAR 60B PDP Safety Precautions Power Supply - Warning AC plug should not be touched with wet hands. It may cause an electrical shock. °§It can cause an electrical shock. Do not use damaged electrical cord/plug, or loose outlet. °§It can cause an electric shock or a fire. Do not use multiple devices in an outlet at the same time to avoid the overload. °§ may cause a fire due to over heating It from the outlet. Power Supply - Warning Fully insert the plug into the outlet °§If the connection is unstable, it may cause a fire. Be careful not to forcibly bend the electrical cords or press them with a heavy object. °§It may cause an electrical shock or a fire. Be sure to ground the PDP power source. °§It may cause an electrical shock if it has a failure or electrical leakage. Only use the proper power cord supplied with PDP and connect it to an outlet with a ground terminal. Power Supply - Caution Wh en un plug ging the AC cord, pull out by holding the plug itself and not by pulling on the cord. °§If the power cord is damaged. it may cause a fire. This manual describes how to operate the PDP properly and safely. [. . . ] Please refer to page 52 for the modes that PDP supports. ). Turning on PDP monitor °§Selecting input signal Before turning on the PDP monitor Insert the power plug. Please use only after carefully reading this manual. Turning on the PDP monitor First check the power connection and check the connection of external equipment. Power On/Off How to turn on PDP monitor - Press the "Main Power Button (A/C input button)" of monitor and then press the Sub-power button. Turn on/off by remote control - Press the power button of remote control (If the monitor is not turned on, check if the "Main Power Button" on the monitor's main body is pressed first. If the "Main Power Button" is pressed, the power indication lamp will be turned on. ) Turning off PDP monitor - Pres s "Sub-Power Button" on the monitor and then press the "Main Power Button". - You can have the power saving effect (Power Consumption Zero) the same as if you unplugged the power cord. °ÿ If ON Time settings are made, make sure that you turn off the monitor with "Sub-Power Button" or remote control. Selecting External Input. Select the required input using button and then select with button in the next menu by pressing input selection (Enter) button. If you know the input connected on the back of the monitor, you can instantly make the input selection by pressing VIDEO button, S-VIDEO button, COMPONENT button, RGB/A button, and RGB/D button on the remote control. EX) When selecting ANALOG RGB, press RGB/A button on the remote control. Volume - Controlling Volume°§Mute - Pausing sound °§Still - Pausing the screen°§Info - Checking current state °§Menu - checking the menu Volume - Controlling Volume Press button to increase volume, Press button to decrease volume. Mute - Pausing sound Press button. If you press the button again, the sound turns back on. Still - Pausing the screen Press button. If you press the button again, the screen moves again. Info - Checking current INFO Press button. The set value that the user has selected appears. It automati- cally disappears after three (3) seconds. Menu - Checking the menu If input selections are "Composite", "S-Video", and "Component", the video menu is activated. If input selections are "Analog RGB" and, "Digital RGB", the computer menu activates. You should use the remote control for detailed menu item setting and change of PDP monitor. Press button. When you press the button, the screen appears in turn as shown in the figure. Use menu. button to move to sub menu and store the setting value. Use button to move main [ Video Mode ] [ Computer Mode ] [ Sound Mode ] [ Equalizer ] [ Setup Mode ] [ Timer Mode ] PSM °§User setting Adjusting video screen How to change the screen mood. Press "PSM" button. Press PSM" button repeatedly to select the desired screen. Standard Dynamic Movie Mild Game User Press button. Press button to move to the item ®ËPress button to enter the sub-menu. ®È Select "Picture" with ®Í Select the required mode with · Standard: It is the best screen state set in the factory. · Dynamic: Select when the surrounding light is bright. · Movie: Select when you watch a movie. · Mild: Select when the surrounding light is dark. · Game: Select to enjoy the game. · User: Select to see the state that the user prefers. (Please refer to page 29 on screen adjustment method. ) User setting - manually setting the screen mode You may change the user setting from any mode. Press the button Press button move to the item ®Ë Press button to enter the sub-menu. ®È Select "Brightness" with . ®Í Set the value with . Press button to return to previous menu. User Mode · Brightness: Adjust the entire screen bright or dark. · Contrast: Adjust the difference of brightness and darkness between the object and the back- ground. · Color: Adjust the color to light or dark. · Tint: Adjust the sense of color of the object naturally. [. . . ] Please refer to page 26. Check if stopped screen of external equipment is pressed. If the screen is still abnormal after automatic adjustment, adjust in user mode. On Time setting works only when turning off the PDP monitor with the remote control or sub-power button. (Because when turning off by pressing the main power button of the monitor, the Timer setting is deleted. The screen appears too slowly after the power is turned on. Screen is too bright or too dark. [. . . ]