User manual PLANAR PE1500 Product Manual

[. . . ] PE1500 LCD Monitor USER'S GUIDE www. planar. com Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Locations and Functions of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Making the Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Using Your Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] See "Doing Adjustment in the "OSD Display" Submenu on page 16. Factory Recall Recall factory-setting values back. See "Doing Factory Recall" on page 17. Language Exit Open the "Language" submenu where you can select one of the five languages for your preference in display OSD messages. See "Selecting Language for Your Preference" on page 18. Clear and exit the OSD main menu. Selecting Items in the OSD Menu To select items in the OSD "Main Menu, you will use the Up() or Down() buttons on the front panel of the display. To select items in the OSD submenus, you will use all three control buttons. To select a specific submenu, you shall use Up() or Down() buttons to move forward or backward to the item to be adjusted, and then select it by press Select button. 9 ENGLISH Item Description Doing Adjustment in the OSD Menu Doing Auto Setup To doing the Auto Setup function you should follow the steps below: 1. The `Auto' icon should be highlighted already. 3. Use `Select' button to select and execute the Auto Setup function. After the execution of the Auto Setup function, it will show-up the follow message: If the image looks correct, choose Yes. OR If the image requires further adjustment, choose No, it will shown up Phase bar for your further adjustment by manual. Then you can adjust phase by Up() or Down() buttons. When all text appears well focused and there is no instability in the image, press the `Select' key to end up the adjustment. 10 To do adjustment in the "Management" submenu you should follow the steps below: 1. Use Up() (or Down()) to move forward (or backward) to the management icon and highlight it. 3. Use `Select' key to enter the "Management" Submenu. It will show up four items for your further adjustment. If Brightness is selected, you may use Up() or Down() buttons to adjust the setting of brightness. The fullness of the graphic bar as well as the numerical value at the right corner are also changed accordingly. Brightness 100 50 50 50 EXIT If Contrast is selected, you may use Up() or Down() buttons to adjust the setting of contrast. The fullness of the graphic bar as well as the numerical value at the right corner are also changed accordingly. 11 ENGLISH Doing adjustment in the "Management" Submenu Contrast 100 50 50 50 EXIT Note: We recommend you do Auto Setup before adjusting the contrast setting. If H. position is selected, you may use Up() or Down() buttons to adjust the setting of the horizontal position of the image. The fullness of the graphic bar as well as the numerical value at the right corner are also changed accordingly. H . position is selected, you may use Up() or Down() buttons to adjust the setting of the vertical position of the image. [. . . ] The message "Signal Out of Range" appears on my display. This message appears when the input signal is beyond the display's capability. Set your PC to a supported video mode, preferably 1024 x 768 at 60 Hz. See "Setting the Video Mode" on page . 6 D. Set your PC to a supported video mode, preferably 1024 x 768 at 60 Hz. [. . . ]