User manual PLANAR PE171 Product Manual

[. . . ] 4 Adjusting the Monitor's Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Function Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chapter 3 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Standard Timing Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Then connect the LCD Monitor and base please. (See fig. 1-1 ) Figure 1-1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted from -5°to +30°. (See fig. 1-2) Figure 1-2 Warning Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the Monitor and Monitor stand. 2 Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull down the hinge to release. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig. 1-3. The rear of this LCD display has four integrated 4 mm, 0. 7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2. 1 and 2. 1. 3, version 1, dated 13 November 1997). Figure 1-4 Connecting the Display 1. Connect one end of the signal cable to the LCD Monitor's VGA port or DVI port. (See Fig 1-5) 3. Connect the other end of the signal cable to the VGA port or DVI port on your PC. Make sure connection are secure. Figure 1-5 Attention This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations. A ferrite-core interface cable is included in the LCD Monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used. Connecting the AC Power 1. Connect the power cord to the LCD Monitor. (See Fig. Connect the power cord to an AC power source. Figure 1-6 Setting Up the LCD Monitor 1. Turn on the LCD monitor's hard power switch, located on the back of the monitor 2. Turn on the LCD Monitor's soft power switch, located on the bezel of the monitor. Figure 1-7 Power Management System This LCD Monitor complies with the VESA DPMS (version 1. 0) Power Management guidelines. The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync. When the LCD Monitor is in power saving mode, the monitor screen will be blank and the power LED indicator will light yellow. 3 Chapter 2 Display Controls User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 1 2 3 4 DC Power Switch DC Power-On Indicator Function Select Buttons Adjustment Control Buttons Press the power switch to switch the monitor ON/OFF. LED lights Yellow --- Monitor is in "Power Saving Mode". Press either left or right control button for OSD (On Screen Display) menu selection. Press the left button to decrease the OSD setting and press the right button to increase the OSD setting. Adjusting the Monitor's Display The monitor has four function control buttons to select among functions shown on OSD menu, designed for easy user-viewing environments. OSD Function Menu To access OSD Main menu, simply press one of the Function Select control buttons, and the menu diagram will pop up on the screen as shown on Fig. 2-2: Continue pressing the Function Select buttons to scroll through the entire menu items , then press Adjustment Control buttons to adjust content of selected item. Figure 2-2 Attention Firmware revision may have been updated into a latest version while the version number shown on all OSD menus in this manual will stay as Ver. [. . . ] Make sure the power indicator on the LCD Monitor is ON, all connections are secured, and the system is running on the correct timing. Refer to Chapter 3 for information on timing. Turn off the LCD Monitor and then turn it back on again. If there is still no picture, press the Adjustment Control button several times. [. . . ]