User manual PLANTRONICS CS10

[. . . ] Cordless Telephone Headset System Pag e Pow er TALK Talk Includes: safety instructions specific operating instructions alternate headset configurations troubleshooting warranty and other information Char ge CHAN NEL MUTE VOLU ME TALK Product Information Booklet WELCOME ge Pa SAFETY INSTRUCTIONS When using your telephone equipment these basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons. 5 This product should never 1 Read and understand all instructions. r Powe Talk ge Char TALK CHANNE L MUTE 2 Follow all warnings and 6 This product should be be placed near or over a radiator or heat register. It should not be placed in a built-in installation unless proper ventilation is provided. operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. [. . . ] First, a short press enables the remote unit to emit two long loud beeps. This allows someone to page you from the base unit. Second, a long press of at least three seconds will enable the remote to emit a continuous ring alert. The ring is deactivated by pressing the talk button on the remote. This is helpful if you misplaced the remote. Page Button Page Visual Indicators On the Remote Unit On the Base Unit Audio Indicators Linked ­ One beep is heard through the headset whenever the base or remote talk button is activated. Low Battery ­ Two beeps are heard, through the headset when in the talk mode at 30 second intervals, whenever the power is low. Out-of-Range ­ Three beeps are heard, through the headset when in the talk mode, whenever the remote is taken out-of-range of the base. Ringer Tone Alert can be activated when using the optional handset lifter. It is a tone emitted by the remote timed with the telephone ringer and can be disabled using the ringer switch on the remote. Disabling the audible ringer does not disable the page function or the ringing heard through the headset. Note: Talk (in-use) ­ green LED `On' only when the remote or base talk button is pushed. Flashes in time with the telephone ringer when the optional handset lifter (see Accessories) is used. Talk (In-Use) Indicator Light MUTE Power ­ red LED `On' whenever power is applied to the base via the AC power adapter. Talk (in-use) green LED `On' only when the remote or base talk button is pushed. Flashes in time with the telephone ringer when the optional handset lifter (see Accessories) is used. TALK CHANNEL VOLUME ­ + Mute Indicator Light Power Indicator Light Talk (In-Use) Indicator Light Page Power Talk Charge Mute ­ red LED `On' only when transmit audio is muted. Battery Charge Light TALK Power Talk Charge 10 TALK Charge ­ amber LED Flashes for two seconds verifying contact when remote is placed in the base charging well. The light remains steady while charging and off when battery is fully charged. 11 TROUBLESHOOTING I cannot hear dial tone I I I hear a buzz or hum I Make sure the telephonehandset is off its cradle. I Make sure the remote unit is within range of the base unit. I Increase the listen volume control. I Remove and replace the AC power cord from the base. My remote stopped working I Return the remote to the charging well for 5 seconds to re-establish a communication link. I Make sure your remote is securely seated in the charging well and/or fully charged. I Separate and then reconnect the battery and remote. Return the remote to the charging well for 5 seconds to re-establish a communication link. I Separate and then reconnect the battery and remote. I Remove and replace the AC power cord from the base. Caller cannot hear my voice I 12 I Check that all cords are correctly connected and firmly in place. Pay special attention that handset and telephone cords are properly connected. Adjust headset so the voice boom is closer to your mouth. I Try adjusting the transmit level switch to position 2 or 1. Move the configuration switch (A/B) to the opposite setting. [. . . ] This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]