User manual PLANTRONICS EXPLORER 260 DECLARATION OF CONFORMITY

[. . . ] 6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 iii Package Contents and Features NOtE Your headset may look different than the illustration, but will still work as described. Headset Front* Volume Control Button Call Control Button Status Light Power On/Off Switch Swivel Earloop [fits either ear] Headset Back Microphone Speaker/Eartip Micro USB Charging Jack Power On/Off Switch AC Charger 100 ­ 240V * For illustration purposes only; designs will vary by model number. iv Charging Your Headset Your new headset performs best when it is fully charged. [. . . ] Connect the charger cable to the headset. 1 1 Charging time 2 hours . . . . . . . . . . . . . . . . . . . . . . . Full charge 1 hour . . . . . . . . . . . . . . . . . . . . . . . . . minimum charge before first use 2 2 NOtE Never charge the battery where the temperature may fall below 32°F (0°C) or rise above 104°F (40°C). Do not use your earpiece while it is connected to the charger. 1 What Is Bluetooth? Bluetooth wireless technology provides a way for devices, like headsets and phones, to communicate with each other without wires. Pairing is the set-up process of introducing your headset to your phone. Before using your headset for the first time, you must pair it with your Bluetooth-enabled phone. Plantronics QuickPairTM Technology To simplify the Bluetooth setup process, your new headset uses Plantronics QuickPair technology. · the first time you turn your headset on, your headset automatically enters pairing mode for 10 minutes. · Until you successfully pair your headset with a Bluetoothenabled phone, every time you turn it on it will enter pairing mode. · to later pair to a new phone, turn on the headset, then press and hold the Call Control button until red then blue flashing appears, which indicates pairing mode status. To check, simultaneously press and hold both the Call Control and Volume buttons for about 2 seconds. The indicator light flashes to show the charge level. Indicator Light Blue flash every 2 seconds until the call is ended. red flashes Battery level 1 2 3 More than 2/3 full 1/3 - 2/3 full Less than 1/3 full Tone Ringing None when checking level. Low battery tone indication: 3 tones when under 5 minutes talk time is remaining. (Two tones at maximum volume level. ) Adjust the volume (during call) Tap the Volume button to Single blue flash for every increase through 4 levels; volume level change. tap at top level to return to lowest volume setting. WARNING Do not use headsets at high volumes for an extended period of time. See www. plantronics. com/healthandsafety for more information on headsets and hearing. 7 Headset Controls and Indicators Action Voice Dial Press and hold the Call Control button until you hear a tone. While the call is in progress, press and hold the Call Control button until you hear a tone. Indicator Light None Tone Single low tone; phone may prompt with "Name please" or tones. Two brief low tones Long low tone when moving to phone; short low tone when moving to headset. Redial last number Transfer a call from headset to phone, or from phone to headset None None 8 troubleshooting My headset does not work with my phone. [. . . ] Callers cannot hear Make sure the headset Power Switch is in the me, or I cannot ON position. hear callers/dialing Your headset may be out of Bluetooth range tone. Move the headset closer to your phone, and make sure your headset and phone are on the same side of your body. Recharge the battery using the supplied AC power adapter. [. . . ]