User manual PLANTRONICS VOYAGER 510-USB

[. . . ] USER GUIDE Plantronics VoYaGErTM 510-UsB BLUETOOTH ® HEADSET SySTEm 0 0 0 T ABLE OF CONTENTS PACKAGE CONTENTS Package Contents Features Charging Powering Pairing Installing PerSono Suite Software Adjusting Fit Using Your Headset Indicator Lights Troubleshooting Technical Assistance Warranty And Service Regulatory Notices ® 3 4 5 6 7 9 10 12 15 18 20 18 18 Headset (Front and Side View) PerSono Suite Software CD 3 Ear Tips (Small, Medium, Large) Headset AC Charger Headset USB Charging Cable Please refer to the separate Safety Instructions booklet for important product safety information prior to installation or use of the product Charging Stand REGISTER YOUR PRODUCT ONLINE Visit www. plantronics. com/productregistration to register your product online so we can provide you with the best possible service and technical support. USB Extension Cable (3') Travel Pouch USB Bluetooth Adapter 3 FEA TURES CHARGING Horizontal Boom Adjustment Call Control Button Charge Connection Noise-Canceling Microphone with WindSmart® Technology AC Charging USB Charging Power/Mute Button Listen Volume Adjust Button +/Ear Tip Pairing/Connect Button AC Charging with Charging Stand USB Charging with Charging Stand Indicator Light Before using, you must first charge your headset. The indicator light flashes red while charging and turns solid blue when the headset is fully charged. 20 minutes = minimum charge 3 hours = full charge NOTE: Do not use headset while charging and do not connect the charger while headset is in use. 4 5 POWERING Powering Headset PAIRING Pairing Headset with Bluetooth Phone Press and hold the power/mute button for three seconds to turn the headset on or off. The indicator light flashes blue when the headset is on. The indicator light will flash red when the battery becomes low. [. . . ] · Headset is not paired to the USB Bluetooth adapter. · When a PC goes into standby or hibernation, the USB Bluetooth adapter no longer is powered on. · Be sure PerSono Suite software is installed and running. See page 9. Problem Sound in headset is distorted. I can hear echo in headset. Solution · Lower the listen volume on your softphone until the distortion disappears. See page 14. The other headset I was using to listen to music does not work any more. · The USB Bluetooth adapter will set itself as the default audio device in Windows® Use the Audio . settings in Windows® under Sounds and Audio Devices to change the device used for audio. · Headset battery may be dead, so be sure the headset is fully charged. · When a PC goes into standby or hibernation, the USB Bluetooth adapter no longer is powered on. Be sure your PC is in an active state. My headset stops responding to button presses. I've plugged in the USB Bluetooth adapter but my headset does not respond to button presses. · Headset is not paired to the USB Bluetooth adapter. · Headset battery needs to be charged. · Headset may be out of range of the USB Bluetooth adapter. Move closer to adapter until the headset is within range. · When a PC goes into standby or hibernation, the USB Bluetooth adapter no longer is powered on. Battery talk time or standby time is significantly degraded even after a full charge. · Battery may be deteriorating. · The headset radio link is locked on. Be sure you do not lock the radio link on for long periods of time as it will significantly reduce standby and talk time of the headset. · One beep every 10 seconds is caused by a low battery warning. Recharge battery by returning headset to the charging stand for one to three hours until indicator light turns blue. · One beep is an out of range warning. Move closer to the USB Bluetooth adapter. · Two beeps every 30 seconds indicate your mute is on. [. . . ] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]