User manual PLANTRONICS VOYAGER EDGE

[. . . ] You hear “welcome” in all the supported languages and then "pairing" in the default language. The headset LED flashes red and blue. 2 Activate Bluetooth® on your phone and set it to search for new devices. • iPhone Settings > Bluetooth > On* • Android™ Settings > Bluetooth: On > Scan for devices* 3 NOTE *Menus may vary by device. Select “PLT_Edge. ” If necessary, enter four zeros (0000) for the passcode or accept the connection. [. . . ] Headset LED behavior for battery status Off Charging complete Battery high Battery low, less than 30 minutes remaining Battery critical , under 10 minutes remaining 8 Use the charge case A fully charged case can supply an additional 10 hours of headset talk time. IMPORTANT The charge case is placed in deep sleep mode after manufacturing to save power and protect the battery. To wake-up the charge case, plug it into a power source for a minimum of 1 minute. The LED's flash when charging. Check the charge case or headset battery status by touching/swiping either the case or headset icons. The LEDs indicate the battery status. Battery status LEDs for charge case and headset Battery high Battery medium Battery low Battery critical; Recharge case/headset 9 Fit Adjust the fit 1 The loop of the gel eartip tucks into the back curve of your ear for a stable fit. With the headset powered off, replace the eartip with one of the two alternate sizes if it feels loose or tight in you ear. 2 To adjust the fit, rotate the eartip on the headset or add the optional clip-on earloop. NOTE If the eartip feels loose after use, remove the eartip, wash it in warm water, let it dry and reattach. 10 The Basics Make/Take/End Calls Answer a call Choose: • Put on the headset to answer call, or • Say “answer” after call is announced, or • Tap the Call button Answer a second call First, tap the Call button call. End a call Tap the Call button to end current call, then tap the Call button again to answer new to end current call. Reject a call Choose: • Say “ignore” after call is announced, or • Press Call button for 2 seconds Call back last call Double-tap the Call button to call back the last active call regardless of whether it was an inbound or an outbound call. NOTE If no calls have been made or received in the current connected session this feature will not function. Double-tapping the Call button will result in a single low tone for each button press; however will not connect you to the last active call from the previous session. Voice dial (phone feature) If your smartphone has a voice-enabled assistant, press the call button wait for phone prompt. for 2 seconds and 11 Caller Announcement (mobile phone only) When wearing your headset, you will hear the name of a contact calling you so you can decide whether to answer or ignore the call without having to check the phone screen. An incoming caller name is announced: • if your phone supports Phone Book Access Profile (PBAP) • if you granted access to your contacts during pairing process (for many mobile phones, this is preset out-of-the box and may not be necessary) • if the caller is stored in the phone's contacts list An incoming caller name is not announced: if the caller is unknown, unlisted, or blocked Mute During a conversation, press the Mute button . You hear “mute on” or “mute off. " An alert repeats every 15 minutes when mute is on. NOTE If the headset smart sensors are enabled (default), mute is deactivated when the headset is taken off and everyone can hear each other. Toggle the Volume button up (+) or down (–) during a call or while streaming audio. While not on a call or streaming audio you can toggle the Volume button to adjust the volume level for Caller Announce and other voice prompts. Smart sensors in this headset recognize if the headset is being worn and can automatically perform time-saving functions. Putting on your headset will: • Answer an incoming call • Transfer an active call from your phone • Resume streaming audio Taking off your headset will: • Transfer an active call to your phone • Pause streaming audio • Lock the Call button to avoid accidental calls Reset sensors You may need to reset the sensors if they are not working as expected. To reset your sensors, connect the headset directly to your computer's USB port, and place it, with the eartip up, on a flat non-metallic surface for more than 10 seconds. Adjust the volume Use Smart Sensors 12 Disable sensors To disable the sensors, hold both the Voice and Call buttons for more than 6 seconds until the LED flashes purple then red. [. . . ] When on a call, you will hear a ringtone notification of the incoming call from the second paired phone. To answer a second call from the other phone, you must end the current call (tap Call button) so the new call automatically answers. If you choose to not answer the second call, it will go to voicemail. Change headset settings You can change the headset settings two different ways. • Download and install the HUB app on your phone (visit plantronics. com/apps)* • Download and install the MyHeadset Updater tool (visit plantronics. com/myheadset) The following headset settings can be changed: • Turn voice commands on/off • Turn high quality audio (A2DP) streaming on/off • Turn Wideband Audio for HD Voice on/off • Customize smart sensors • Customize mute Update headset firmware 1 2 You can update your headset firmware using a USB cable and computer with the MyHeadset Updater tool installed. [. . . ]