User manual PLUS BF-030 W Operation Manual

[. . . ] 3 HOW TO USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 MAINTENANCE/HOW TO STORE . . . . . . . . . . . . . . . . . . . . . 7 HANDLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 CHECK LIST OF SIMPLE FAILURES . . . . . . . . . . . . . . . . [. . . ] PC COPY key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Feed/stop key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . This is used when the screen slides to the left. Pressing this key advances the screen by one page and then automatically stops. Pressing the key while the board screen is being moved stops it immediately. This can also be used when paper has run out and must be refilled. If this key is pressed during the copying operation, the copying performance ends and the printer stops. 3 HOW TO USE BEFORE USE. . . Press the caster lock switches ON and keep the casters in a locked position. After the power lamp blinks for 2-3 seconds, it should turn green. POWER POWER ON PAPER OUT WHEN COPYING. . . When copying onto A4 paper: Press the A4 reduction copy key. At this time the board screen slides forward one page and the written contents are reduced onto A4 paper. When copying onto A4-L paper: Press A4-L copy key. At this time the board screen slides forward one page, and the written contents are reduced to A4-L size (210 x 400mm) and copied. Cut-off of Recording Paper When copying is completed, pull the tip of the recording paper upwards and cut it off with the edge of the outlet. Halt of Copying Press the feed/stop key to half the copying operation immediately. The printer stops after completion of copying up to that point. 4 HOW TO USE WHEN SLIDING THE SCREEN FORWARD. . . Sliding by using key Press the feed/stop key. Then, the board screen slides to the left by one page and stops. It stops immediately when the feed/stop key is pressed during the sliding operation. Manual sliding It is also possible to slide the board screen manually. In this case, it can be slid in either direction; to the right and left. However, manual sliding at an excessively high speed must be avoided as it occasionally causes problems. WHEN REPLACING RECORDING PAPER. . . *Concerning replacement of recording paper Replace with new recording paper in the following cases: When a red line appears at the end of the recording paper. (A red line appears when only about one meter or so of recording paper is remaining. ) When the paper warning lamp lights red. Press the opening button to open the printer cover. Take out the winding core of used recording paper. As illustrated, set it in so that the tip of the new roll of recording paper extends about 20cm from the outlet. 5 HOW TO USE Push both ends of the hatch closed until it locks with a clicking noise. At this time, make sure that the recording paper has not slipped. Cut off the extra recording paper from the printer outlet. Replace the recording paper in the following situations When a red line appears at the edges of the recording paper. The red line will appear when there is only about one meter (3 feet) or so of recording paper left on the roll. When the paper out lamp lights red. Note: Please use only the correct type of recording paper. [. . . ] In addition, when it is not to be used for a long time, make certain that the plug of the power cord is pulled out form the outlet. Be careful not to use other markers as the sheet may be damaged or, in some cases, the ink may be difficult to remove. Write within an area of a size that can be easily read. 20mm 30mm 30mm 20mm 11. When moving this machine, turn OFF the caster lock switches, hold both the right and the left sides of the main unit firmly, and avoid any sudden jolts or shocks. CHECK LIST OF SIMPLE FAILURES <BEFORE ASKING FOR A REPAIR SERVICE> CONDITIONS When the power fails When pressing copy key does not result in copying Although printer is functioning, nothing is copied on recording paper When characters written on board screen cannot be rubbed out even by the use of an eraser When copy is dirty CHECKPOINTS Check if power cord is pulled out outlet. [. . . ]