User manual PLUS M-10

[. . . ] Copyboard with Memory Function M-10S/M-10W User's Manual Thank you for your purchase of the PLUS Copyboard. Please read this User's Manual carefully before use to take full advantage of the functions of this product. After you have finished reading the manual, please keep it for future reference. This User's Manual covers both models M-10S and M-10W. The copyboard is available in a standard size (model M-10S) and a wide size (model M-10W). [. . . ] See Page E-19. Press the POWER button and switch on the power. POWER OK Cancel COPY Note When the POWER button is pressed and the power is turned on, the LED on the display shows a countdown of approximately 25 seconds, then the LED stops flashing, remaining lit. The copyboard is checking its status during this time. MEMORY REPEAT FEED/STOP When the drawing is on the rear sheet, press the FEED/STOP button to bring out the desired surface for printing. FEED/STOP Density MemoryClear A press of the FEED/STOP button scrolls the sheet surface one screen portion left and automatically stops it. (The M-10S takes approximately 15 seconds and the M-10W takes approximately 20 seconds. ) To stop the operation part way through, press the FEED/STOP button again. POWER COLOR Note * The one-screen that is visible is printable position. * To make fine adjustments to the sheet surface, when the sheet is stopped, move the sheet slowly by hand. The sheet can be moved either left or right. * The peripheral area of the sheet surface is not printed. Please see "Effective reading size" on Page E-8. Press the COLOR button and select Color or Black & White. COLOR COLOR lamp Lit . . . . . . . Printing will be in black & white. · At first, when the power is switched on, black & white is selected. Note If a black and white printer is connected, the selection is ignored and printing is performed in black and white. Continued on next page E-12 Press the + button or the - button and select the number of copies. Selecting the printing density Select this when the density of the print is light. Press the Density button and select darker or standard. Density indicator Lit . . . . . Standard Density · When the power is switched on, one copy is selected. · A maximum of 20 copies can be set and the number of copies is displayed in the display window. · Each press of the + button increases the number of copies (by one) and each press of the - button decreases the number of copies. Press and hold the button to switch continuously. Press the COPY button to print. COPY Making additional copies This will print the copy of the sheet that was scrolled previously one more time. Press the REPEAT button. · The reading operation is performed for a one-sheet portion (while the sheet is scrolled) and printing starts after the scrolling completes. This starts the printing of the image data that has accumulated in internal memory. REPEAT Note · A press of the FEED/STOP button during the reading operation will cause the printing to stop and will result in a partial print. To move the sheet surface, please press the FEED/STOP button after the scrolling has stopped. · When a CompactFlash card has been inserted, a press of the MEMORY button during printing will start the memory storage operation after printing is completed. (See Page E-15. ) · The one-screen portion is reduced to A4 paper size and printed. In the wide type (M-10W) copyboard, the screen will be reduced to about 71% in the horizontal direction. When the copyboard is not going to be used, press the POWER button and switch off the power. POWER Note · The sheet is not scrolled when additional copies are made. · The number of copies can be changed. To do so, make the change before pressing the REPEAT button. · In repeat printing, the color/black & white and density settings will be the same as those of the prior printing. · When printing or memory storage has not been performed since switching on the power, image data will not have accumulated in the internal memory and this operation will not be possible. · Switch off the printer power. Note · In the absence of button operations, the fluorescent lamp will be switched off after 30 minutes. [. . . ] When connections are completed, fasten the cable with the supplied cable clips. AC INPUT connector Printer connector Wall outlet Power cable (supplied) USB connector USB cable (supplied) AC INPUT power connector Power cable supplied with the printer E-23 CHANGING THE HEIGHT OF THE UNIT This is the height adjustment when setting up the copyboard on the optional stand. The stand height can be adjusted to 3 levels in 100 mm units. CAUTION! Please have 2 or more persons hold the unit. If the unit is dropped or falls over, this could cause unexpected injury. Please lock the casters by pushing the lower portion of the lock button. (1) Disconnect the power cable and all other connection lines. (2) Take out the printer and remove the printer tray. Remove the two M4 screws from bottom side of the printer stand and the other two from the rear surface. (3) Remove the two lock knobs (located at the left and right sides). [. . . ]