User manual PLUS U3W

[. . . ] DATA PROJECTOR U3-1100/U3-810 USER'S MANUAL English Applicable Models: U3-1100WZ, U3-1100W, U3-1100SF U3-810WZ, U3-810W, U3-810SF PLUS IMPORTANT Digital Light Processing, DLP, Digital Micromirror Device and DMD are all trademarks of Texas Instruments. Windows 98, Windows 95, and Windows 3. 1 are registered trademarks in the United States and other countries of Microsoft Corporation. IBM is a registered trademark of International Business Machines Corporation. Macintosh and MAC are trademarks of Apple Computer Inc. [. . . ] 2Rotate the contact surfaces of the rear adjuster either clockwise or counterclockwise to accurately adjust the level. Zoom ring Focus ring Using the unit (continued) Using the Remote Control (Input Selection) 9 10 Adjust the picture elements (see page 22), then select the picture type according to the video content (see page 26). MOUSE MENU POWER Start using the unit. The following functions are available while using the unit: · Adjusting the volume of the unit's speaker (see pages 18 and 28), · Turning off the image and muting the sound temporarily (see page 18), · Freezing a moving picture (see page 18), · Enlarging the picture (see page 19A) Note · When there is no signal input for a period of 5 min. or more, the power is automatically turned off and standby status is activated. (see page 29) VIDEO button VIDEO CANCEL RGB RGB button Operating from the main unit Inputs can be selected not only by operating the remote control but also by using the main unit SOURCE button. POWER STATUS POWER SOURCE AUTO SOURCE button 1 Press the VIDEO button. The video signal (VIDEO, S-VIDEO) connected to the input jack of this device will be detected and projected automatically. If a video signal is not detected, the message NO SIGNAL will be displayed. After using the unit VIDEO 1 Press the POWER button of the remote control or the POWER button of the main unit for a few seconds. The power will turn off and the POWER indicator will blink amber for 1 min. , then the standby status will be activated. (The exhaust fan will continue to run for a while for cooling purposes. ) Do not unplug the power cord while the indicator is blinking. MOUSE MENU VIDEO CANCEL RGB POWER POWER ST 2 Press the RGB button. The analog RGB signal connected to the input connector of this device will be detected and projected automatically. (Component video will be detected if the RGB/ YCbCr connector is set (page 27) to YCbCr. ) If a video signal is not detected, the message NO SIGNAL will be displayed. RGB POWER Note Blinks amber (1 min. ) Lights amber Note · All video signals input to this device will be detected if Auto Source (page 29) is set. 3 Press the SOURCE button. The video signal (RGB or YCbCr, VIDEO, SVIDEO) connected to the input jack of this device will automatically be detected and projected. If a video signal is not detected, the message NO SIGNAL will be displayed. SOURCE · The POWER switches of the remote control and main unit will not operate until the blinking stops. · After the standby status is activated, wait 1 min. or more before turning the power on again. The power will not turn on until the 1 min. · The exhaust fan will continue to run even in standby status. 2 Disconnect the power cord. The POWER indicator will turn off. The signals are sensed repeatedly in the sequence shown below. RGB/YCbCr S-VIDEO VIDEO Note · When Auto Source (see page 29) is set to ON, all signals input to this projector will be sensed. E ­ 16 Using the Mouse Remote Control as the PC The remote control of this projector can be used as the PC mouse (wireless mouse function) by connecting the MOUSE connector of this projector and the PC. Remote control mouse functions · When the MOUSE button on the remote control is pressed, the button is lit in red. This red light shows that the cursor key on the remote control operates the computer mouse function. When the MOUSE button is pressed again, the button's light goes off. In this condition the cursor key operates the projector cursor function. MOUSE button · If a computer running Windows is connected, the ENTER button on the remote control operates as the computer mouse left click button and the CANCEL button as the computer mouse right click button. · If a Macintosh computer is connected, the ENTER and CANCEL buttons operate in the same way as the computer mouse click button. MOUSE POWER MENU VIDEO RGB CANCEL Connecting a PC and the MOUSE connector of this projector Before connecting a PC · Before connecting, turn off the PC power. Turn off the power of this projector if it is on. · When connection is completed, turn on the power of this projector and then start the PC. USB Port Connection Connect the supplied USB mouse cable directly to the USB port (universal serial bus) of the personal computer, as shown in the diagram. Personal computer USB port IBM PC/AT or Macintosh MOUSE connector USB mouse cable (accessory) AUDIO MOUSE RGB / YCbCr S-VIDEO VIDEO To PS/2 MOUSE port IBM PS/2 compatible PS/2 mouse cable (accessory) IBM PS/2 Mouse Port Connection Connect the supplied PS/2 mouse cable to the personal computer, as shown in the diagram. Note · Depending on the personal computer, the mouse may not be recognized in some cases if not connected to the MOUSE connector before the personal computer power is turned on. · In the case of some notebook and laptop type personal computers, it may not be possible to use the standard pointing device (track ball, etc. ) of the personal computer when connected to the MOUSE connector. [. . . ] (See page 33. ) E ­ 32 Replacing the lamp cartridge Step 3 The rated lamp life is about 1, 000 hours. The rated lamp life is the average life of the lamps produced and tested (under the test conditions of our company) for a long term, however, it may become shorter depending on the conditions of usage. After the lamp has been operating for 1000 hours or longer, the STATUS indicator on the control panel will light and the "LAMP USAGE" icon which shows hours of total lamp usage will be displayed on the screen. When this happens, turn off the unit and replace the lamp cartridge with a new one. [. . . ]