User manual PLUS U5-532

[. . . ] DATA PROJECTOR User's Manual SO UR CE (U5-532h/U5-512h) (U5-632h) M O ZO 2 4 R E TIM / K L LIC E -C C R AN C TE U M R E S LA TO U A O E ID V K IC U Q (U5-732h) Y B D N TA S B G R U N E M R TE N E Q FR EE ZE 1 L O V 3 IMPORTANT * DLPTM (Digital Light Processing) and DLPTM chip are registered trademarks of Texas Instru-ments Incorporated (U. S. A. ). * DLPTM chip is an ultra-precise part developed by Texas Instruments (U. S. A. ) which takes the place of liquid crystal (in the projector). * VGA and XGA are trademarks or registered trademarks of International Business Machines Corporation (U. S. A. ). * S-VGA is a registered trademark of Video Electronics Standards Association. [. . . ] The volume adjustment display appears when one of the buttons is pressed. LASER RGB ENTER RGB VIDEO AUTO VIDEO CANCEL QUICK MENU QUICK Q Q FREEZE MUTE ECO AUTO (2) 1 2 3 4 ASPECT ENTER R-CLICK/ CANCEL VOL KSTN ZOOM TIMER The button increases the volume and the volume. button decreases the (2) FREEZE MUTE TIMER 1 2 ZOOM (2) Press the CANCEL button to immediately close the display. The display will close when there has not been an operation in about 10 seconds. VOL 3 4 (1) Note: * Adjustment of the volume will not produce any sound unless an image is being projected. * Please make connections to the AUDIO connectors of the projector with the supplied audio cable. (1) E-31 General Operation Enlargement of the Image and Video Movement This function digitally enlarges the personal computer image and video image. (1) Press the ZOOM button to enlarge the image. The zoom display appears when the ZOOM button is pressed. STANDBY LASER RGB VIDEO AUTO MENU QUICK Q (2) ENTER R-CLICK/ CANCEL Each press of the button enlarges the image and each press of the button makes the image smaller (returning it to 1:1). (3) FREEZE MUTE TIMER 1 VOL 2 ZOOM (1) 3 4 Zoom 0 Zoom 21 (No enlargement) (Approximately 2 times enlargement) STANDBY MENU RGB ENTER VIDEO CANCEL QUICK (2) (3) (2) Pressing the SELECT ( ) buttons on the remote control at the time of the zoom operation will cause the display position to move. (There will not be any movement when zoom is at 0. ) Q FREEZE MUTE ECO AUTO 1 2 3 4 ASPECT VOL KSTN ZOOM TIMER (1) Zoom 21 Zoom 21 (Approximately 2 times enlargement) (Movement) (3) Press the CANCEL button to immediately close the display. The display will close when there has not been an operation in about 10 seconds. Note: After magnifying the image, be sure to use the ZOOM button to bring the gauge value back to "0". The image can also be moved in the following circumstances. · · When "Aspect" is set to "Real" by the signal of the personal computer, and the input resolution is higher than the display resolution of the projector. When "Aspect" is set to "Zoom" by the video signal. Note: * Zoom and image movement functions are cancelled when the input is switched. * The greater the zoom enlargement, the less distinct the image will appear. The reason for this is that the dots are being digitally corrected so that they are not conspicuous. * Movement of the screen will not be possible when the menu screen is being displayed. E-32 General Operation Using the Presentation Timer The presentation is given while checking the timer displayed on the screen. The gauge display allows the remaining time to be known at a glance. (1) Press the TIMER button to show the settings display. The display will close when an operation has not been made for about 10 seconds. (2) ENTER STANDBY LASER RGB VIDEO AUTO MENU QUICK Q R-CLICK/ CANCEL CANCEL button (1) (3) FREEZE MUTE TIMER 1 2 ZOOM [Timer settings display] Press the CANCEL button to close the display immediately. (2) Use the and SELECT buttons to set the time. The setting contents are "Off" and from 10 to 60 minutes (in 10-minute intervals) Settings can also be made with the SELECT ( ) buttons. VOL 3 4 STANDBY MENU (2) CANCEL button (3) RGB ENTER VIDEO CANCEL QUICK Q FREEZE MUTE ECO AUTO (3) Press the ENTER button and start the timer. · The display of the timer setting will close, the display of the timer will appear and simultaneously the timer will start. Gauge (Blue) [Timer Display] The blue gauge indicates the remaining time. When the gauge disappears, the time is up. The gauge continues to be displayed when the timer is stopped. When the remaining time is "0" (Gray) · Press the ENTER button to restart the timer. [. . . ] · If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can be heard and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may cause injury. If this happens, contact your dealer or the store the projector was purchased. E-64 Replacing the Lamp Cartridge Preparations: Turning the projector upside-down on top of a soft cloth, etc. , so that it does not get scratched makes it easier to replace the lamp cartridge. [. . . ]