User manual PLUS U7-132

[. . . ] DATA PROJECTOR U7-132/U7-137 User's Manual B IN RG UT BO RG R E TIM / K L LIC E -C C R AN C TE U M R E S LA TO U A O E ID V K IC U Q IMPORTANT * DLPTM (Digital Light Processing) and DMD (Digital Micromirror Device) are registered trademarks of Texas Instruments Incorporated (U. S. A. ). * PC/AT, VGA and XGA are trademarks or registered trademarks of International Business Machines Corporation (U. S. A. ). * S-VGA is a registered trademark of Video Electronics Standards Association. * Microsoft, Windows, and PowerPoint are registered trademarks of Microsoft Corporation (U. S. A. [. . . ] Connecting the computer and projector Use the USB cable included with the projector to connect the computer's USB (type A) connector to the projector's MOUSE connector. Note: * Be sure to plug the cable in securely. * Depending on the type of connection, the computer's operating system, etc. , it may be necessary to change settings or restart the computer after making the connections. USB connector USB cable (mini B to A type) (Supplied item) Functions of the mouse function buttons When operating, point the remote control unit's transmitter towards the remote control sensor on the projector. L-CLICK button (on back) Press this to perform the left-click operation. LASER VIDEO AUTO STANDBY RGB MENU QUICK JOG buttons These move the computer's pointer in the corresponding direction. R-CLICK button Press this to perform the right-click operation. Q ENTER R-CLICK/ CANCEL FREEZE MUTE TIMER 1 VOL 2 ZOOM INFORMATION The R-CLICK/CANCEL button is used for both the projector and mouse function. When the R-CLICK/CANCEL button is pressed while a menu is open, the menu is closed. 3 4 Note: Connections with USB Cables * For PC/AT compatible computers, this function cannot be used with operating systems other than Windows 98SE, Me, 2000 and XP. For Macintosh computers, this function cannot be used with operating systems other than OS 9 and later. * When the cable is disconnected and then reconnected to the USB port of the personal computer or the MOUSE connector of the projector, allow at least 5 seconds before reconnecting. Do not repeatedly disconnect and reconnect the cable in a momentary fashion. The personal computer may not be able to correctly identify the projector as a result. * The supplied USB cable is a dedicated cable for this projector. There is no guaranty that it will work in connections with other USB equipment. * This function may not work with some computers. E-32 General Operation Controlling the Projector from a Computer Use the control connector if the projector cannot be operated with the remote control unit, for example when it is suspended from the ceiling. RS-232C connections Use the order-made cable (D-Sub 9-pin/DIN 9-pin) to connect the computer's RS232C connector to the projector's "PC CONTROL" connector. RS-232C connector Order-made cable (D-Sub 9-pin/DIN 9-pin) Order-made cable (D-Sub 9-pin/DIN 9-pin) pin assignment 4 1 2 5 3 7 8 1 6 6 9 5 9 CN-1 (DIN 9-pin side) Pin assignment CN-1 (DIN 9-pin) CN-2 (D-Sub 9-pin) 1 (TXD) 3 (PC-TXD) 2 NC 3 NC 4 (GND) 5 (GND) 5 NC 6 NC 7 (RXD) 2 (PC-RXD) 8 NC 9 NC CN-2 (D-Sub 9-pin side) Connecting via a LAN U7-137 only It is also possible to control the projector with Telnet connections via a LAN or wireless LAN (using PLUS projector control commands). Note: * This function may not work with some computers. * Specialized knowledge is required to use the control connector. Consult a specialist, such as the person suspending the projector from the ceiling. * Have the order-made cable made by a specialist with the required specialized knowledge based on the pin assignment shown above. E-33 General Operation Protecting the Projector with the Security Lock A password can be registered and the security lock set in order to protect the projector from unauthorized use. Registering the password The password is registered using the menus. For instructions on operating the menus, see "Menu Operation Method" on E-37. (1) Select "Security Lock" in the "Option" menu and set it to "Enable". The menu closes and the password registration display appears. (2) Use the number buttons (1 to 4) to register the password. Example: Registering the password "2441" (1) Press number button "2". An " " (asterisk) appears at the first place. Next press number buttons "4", "4" and "1" in that order. Asterisks appear in all four places. STANDBY LASER * RGB VIDEO AUTO MENU QUICK Q ENTER R-CLICK/ CANCEL FREEZE MUTE TIMER 1 2 ZOOM (2) Input the password again. [. . . ] · Do not remove any screws other than those specified. · Do not touch the lamp with bare hands. Doing so could shorten the life of the lamp. · If lamp has reached the end of its usable life, the lamp bulb may shatter. [. . . ]