User manual PLUSTEK OPTICBOOK 3600 CORPORATE

[. . . ] 2 A NOTE ABOUT ICONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SYSTEM REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BOX CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PRODUCT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Plustek USB Scanner (TWAIN) window will open. CLOSE the Guided Scan window and click the SCAN button. If an image appears on your screen, your scanner is working properly. If an image appears on your screen, your scanner is working properly. To learn how to manipulate the image, please read the Chapter II. The Scanner Software section of the Scanner Software User's Guide. 11 Attention Note: If the test failed in any way, please read The Scanner Utility Program section of this manual and follow the instructions therein. The Scanner Utility Program The Scanner Utility Program can help you get your new scanner up and running. In addition, it contains a number of other features to help you tailor and control the scanner. Most significantly, the Scanner Utility Program checks to make sure that the scanner software is properly installed and the scanner and computer are communicating with each other. Two other features of the Scanner Utility program are the scanning lamp controls and the scanning position alignment utility. The Scanner Utility allows you to turn the scanning lamp on and off, and define an idle time for the scanning lamp to automatically turn itself off. Also, it allows you to define the exact position on the scanning glass where scanning will begin. In the window that opens, find the Lamp Control section shown below: Click on the On/Off switch at the far right of the section to immediately turn the scanning lamp on or off. You may also set the default time for the lamp to automatically turn off after a scan by clicking the up or down arrows next to the area that reads "minutes to turn off lamp. " Maintenance To keep your scanner working smoothly, take a moment to review the following maintenance tips. · Avoid using the scanner in a dusty environment. When it is not in use, keep the scanner covered. Dust particles and other foreign objects may damage the unit. · Do not attempt to disassemble the scanner. There is danger of an electrical shock and opening your scanner will void your warranty. · Do not subject the scanner to excessive vibration. · Be sure not to bump or knock the scanner glass as it is fragile and could break. · Clean the scanner glass by lightly spraying a non-abrasive glass cleaner onto a lintfree cloth. Then, wipe the glass thoroughly with the cloth. [. . . ] The manufacturer warranty includes all parts and labor, and is not valid without the receipt of original purchase. To obtain warranty service, you may contact the authorized dealer or distributor, or visit our website to check out the available service information, or send a request via E-mail for further help. If you transfer this product to another user, warranty service is available to that user for the remainder of the warranty period. You should give your proof of purchase and this statement to that user. [. . . ]