User manual POCKETWIZARD MINI TT1 QUICK GUIDE FOR NIKON

[. . . ] PocketWizard channels are used instead of Nikon channels. See Learn Mode section. CLS / i-TTL Basic Wireless CLS / i-TTL: MiniTT1 No flash on Camera FlexTT5 1. Slide Speedlight onto remote FlexTT5 Transceiver. Set the Speedlight for standard i-TTL mode (not REMOTE or MASTER). [. . . ] Note: Manual remote flashes are not calculated as part of the i-TTL exposure. Adjust your exposure or FEC to compensate accordingly. Use PocketWizard Utility to engage HyperSyncTM and explore faster than X-sync shutter speeds. Visit www. PocketWizard. com for more information. Learn about the AC3 ZoneController, PowerTracking, and controlling your Speedlights and select studio flashes by reading the extended documentation for the following PocketWizard radios and accessories: · AC3 ZoneController for Nikon · PowerST4 for Elinchrom · AC9 AlienBees Adapter for Nikon Learn Mode Channels can be set via PocketWizard Utility (recommended) or taught from any PocketWizard transmitter using Learn Mode. Learn Mode is not required for normal operation of the radios. IMPORTANT: Hold radios at least 2 feet apart when teaching/learning. 1. Turn MiniTT1 or FlexTT5 radio ON and select channel to be taught: C. 1 or C. 2. Press and hold TEST for several seconds until LED blinks amber, then release TEST. Quickly press and hold TEST on teaching transmitting radio (MiniTT1, FlexTT5, Plus II or MultiMAX). When LED blinks green, channel is learned. Connected flash may trigger during Learn. · 1 green blink = Low Standard channel learned (1 through 16, including Plus 1 through 4) · 2 green blinks = High Standard channel learned (MultiMAX 17 through 32) · 3 green blinks = ControlTL channel learned For remote i-TTL systems, teach MiniTT1 radio to be used as primary transmitter first, then use it to teach all FlexTT5 units. MiniTT1 and FlexTT5 radios send out both ControlTL and Standard triggers every time they are triggered. For remote i-TTL to function, ControlTL channel must be learned. If you see only 1 or 2 green blinks, and you desire i-TTL, teach again with MiniTT1 or FlexTT5 radio. Look for 3 green blinks to verify ControlTL is learned. To teach all radios Standard channels, use Standard transmitter as teaching radio for all learning radios, including MiniTT1 radio to be used as primary transmitter. To avoid inadvertent flashing, turn OFF remote radios that have already been taught or have already had the channel set. a Other Functions Auto-Relay Mode A FlexTT5 radio in camera's shoe and connected with motor drive cord to P1 can receive a radio trigger and trigger the camera's motor drive, which in turn triggers a remote flash. The channel used for relay transmit is 1 higher than receive channel, unless set differently via PocketWizard Utility. Example: If you taught FlexTT5 radio Standard channel 2, then relay transmit occurs on Standard channel 3. Press TEST on hand-held trigger radio to begin relay sequence. [. . . ] For warranty details, and to register your product, please go to www. PocketWizard. com/support or contact your local PocketWizard Distributor. Distributor contact information can also be found at www. PocketWizard. com. To receive a copy of the two-year limited manufacturer's warranty on this PocketWizard product, e-mail us at warranty@lpadesign. com or write to us at LPA Design, Inc. , 21 Gregory Drive, Suite 140, South Burlington, VT 05403, United States of America, Attn: Warranty. Frequency IMPORTANT: US FCC/Canada frequency radios are NOT compatible with CE frequency radios or Japan frequency radios and vice versa. For more information on frequency, please go to: www. PocketWizard. com/wheretobuy/frequency © 2010 LPA Design, Inc. [. . . ]