User manual POLAROID PLA-4200M

[. . . ] PLA-4200M WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The plasma monitor shall not be exposed to dripping or splashing. No object filled with liquids, such as vases, shall be placed on it. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : This important warning is located on the rear of the cabinet. CAUTION: Do not place this Plasma Monitor on an unstable cart, stand, or table. The Plasma Monitor may fall, causing serious injury to a child or adult, and serious damage to the Plasma Monitor. Use only with a cart or stand recommended by the manufacturer or sold with the Plasma Monitor. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 Read these instructions. [. . . ] How to setup TV reception 1 Auto channel Press the TV/VIDEO button on the remote controller TV SETUP SET UP DOWN EXIT to select the TV status. AUTO CHANNEL Press SET Press CH+ or CH- button to open the TV SETUP FINE TUNE 50 menu (a). Press MENU button to enter the Setup mode and press CH+ or CH- to select the MODE item. Press VOL+ or VOL- to select Cable or Air Press CH+ or CH- to select AUTO CHANNEL. Press the MENU button to begin the automatic search and store. . 2 FINE TUNE If the image receiving is poor, press CH+ or CH- to select FINE TUNE item in menu (a). Press VOL+ or VOLto adjust the picture quality. 3 Select the TV channel Press the CH+ or CH- button on the remote controller to switch to the previous and next channel of the current program. Press the 0-9 digit button and 100 button on the remote controller to select either AIR for channels CH2-CH69 or CABLE for channels CATV1-CATV125 To channels in each mode: Air channels CH2-CH9: press the appropriate 2-9 digit button directly. Air channels CH10-CH69: press 2 digit buttons in sequence. Cable channels CATV1-CATV9: press the appropriate 1-9 digit button directly Cable channels CATV10-CATV99: press 2 digit buttons in sequence. Cable channels CATV100-CATV125: press the 100 button first, then press the necessary digit buttons in sequence. 4 CH ADD/ERASE is used to add and erase channels which were programmed with AUTO CHANNEL. Select the channel to erase by pressing the 0-9 and 100 buttons or the CH+ and CH- buttons on the remote controller. With the channel selected, press the CH ADD/ERASE button to erase the channel. changes from yellow to blue when it is erased. To restore an erased channel, select the blue Channel No. and press the CH ADD/ERASE button. Note: Please keep at least two stored channels. (The Channel Number is blue. ) Cable Mode has three modes:CABLE-STD, CABLE-HRC and CABLE-IRC. Please choose the suitable mode depending on your local situation. TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA CONTENT TV GUIDELINE SHOW BLOCK BLOCK BLOCK BLOCK BLOCK Press SET D L S V FV 9 BLOCK CONTENT D L S V FV UP DOWN LEFT SHOW BLOCK BLOCK BLOCK BLOCK RIGHT EXIT PASSWORD CHANGE OLD NEW CONFIRM ---------EXIT B. TV GUIDELINE Select TV GUIDELINE item in menu (d). Press MENU button to confirm, the image (f) will appear on the screen. Press CH+ or CH- button to select the rating( excluding CONTENT). Press CH+ or CH- button to select SOUND menu, the image (k) will appear on the screen, then press MENU button to confirm. [. . . ] from TV to AV. XVI Technical specifications Type System of the broadcasting signal System of the video signal Number of Stored programs Scope of the channel Signal Intensity Audio Speaker output Audio input (speaker) PC/DTV RGB input Max. visual angle PLA-4200M NTSC-M PAL/NTSC/SECAM 125 AIR CH2-CH69 , CABLE CATV1-CATV125 >=70dB Input impedance >10K . input voltage 0. 1-0. 5Vrms 2X5W PC YP B P R HDTV(the supporting format is in the attached table) Vertical angle <=30 Horizontal angle <=150 852X480 AC 100V-240V 350W(MAX) 42 inch 16:9 110 pound 0~35 20%-70%RH 86~106Kpa (50 Hz /60Hz) 3W(Standby) 14 Resolution Power supply Energy consumption Dimensions of the whole set Size of the screen Width Height ratio of the screen Weight Ambient temperature Ambient humidity Ambient air pressure 14 (Width/Height/Depth)46. 1X29. 1X15. 2inch Note: The specifications is subject to modification without notice . XVII Troubleshooting If there is any abnormal situation during the operation, please make the corresponding check according to the following instruction before sending for repair. No video signal Check the connection of the power cord. Check if the unit is under standby status. [. . . ]