User manual POLAROID PLA-4237

[. . . ] 42" Plasma EDTV with ATSC Tuner PLA-4237 20060306 Table of Contents Polaroid. Add a little color to your life. Since 1937, America has turned to Polaroid for their photography needs. Today, families look to Polaroid for consumer electronics that define the digital age: plasma and LCD TVs, portable and standard DVD players, digital cameras. And while our selection has changed, you'll still receive the same friendly, helpful service that made Polaroid an American icon. [. . . ] To quit, press EXIT button. Channel Labels Menu NTSC Ch005 ---- To Move OK To Change Exit To Exit 4 19 Channel Selection Information about USA channel numbering ?ATSC PSIP channel has two part channel number: -- Major channel number Þ Frequency -- Minor channel number Þ Sub channel on frequency ?In USA, the major channel number is same for both analog and digital frequencies. (It is equal to the NTSC channel number for existing broadcasters. ) ?In USA, a minor channel number of zero is used for a broadcaster's analog channel. Channel Numbering Example ?Original NTSC Channels for Des Moines: -- 5, 8, 11, 13, 17 ?Possible NTSC + ATSC Channels for Des Moines: -- 5-0, 8-0, 11-0, 13-0, 17-0 (channel numbers for existing analog channels, all on original NTSC analog frequencies) -- 5-1, 5-2, 8-1, 8-2, 8-3, 8-4, 13-1 (channel numbers for digital channels on three new digital frequencies) Channel Selection Using the Channel up/down buttons (CH+ or CH-) Press the CH+ or CH- to cycle among available channels found. Using the direct select buttons (0-9 and dot buttons) Press the number buttons (0-9) and the dot button (l) to go directly to a channel. For example, if you want to select channel 8-3, just key in `8', `l', `3' on the remote control. Note: =When you use the number buttons, you can directly select any channel within the channel range . =In some situations virtual channel numbers have no correspondence to physical frequencies. Using the LAST button Press this button to switch between the current channel and the last viewed channel. 20 Setting Picture Customizing the Picture Video 1 2 3 4 5 Press MENU to display the menu main page. Picture Mode Contrast 50 Brightness 50 Color Sharpness Aspect Ratio Advanced Video Menu 50 0 User Press 5or6 repeatedly to select Video menu. Press OK or4 to access the submenu. Audio Setup Wide Feature Within the menu, use 5, 6, 3or4 to navigate or adjust. Press OK or 4button to confirm, enter sub-menu or toggle Notes: the settings of the selected menu item. The OSD illustration shown above is Video menu in RF(TV) mode. The menu items may be different when the unit works in different mode. To Move OK To Select Exit To Exit Option Function Choice/remarks User/Nature/Soft/Bright Picture Mode Contrast Brightness Selects a desired picture mode. Adjusts screen brightness for easier viewing of dark picture such as night scenes and black hair. Adjusts image sharpness and displays a sharp image. Reduces noise in the picture, commonly called snow. Adjusts tint for image. Selects one of three automatic color adjustments. Sets to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue. Note: you may directly press PICTURE MODE button on the remote control to select. 4: stronger 3: weaker 4: lighter 3: darker 4: stronger 3: weaker 4: sharper 3: softer Color Sharpness Aspect Ratio Noise Reduction--Spatial Wide/Cinema/Normal/Zoom Note: you may directly press ASPECT button on the remote control to select. Advanced Video Menu Noise Reduction--Speckle Noise Reduction--Temporal On/Off 4: greenish 3: purplish Tint Color Temperature 3D Y/C Cool/Warm/Normal Selects 3D comb filter on/off, normally please select On. On/Off To still the picture Press the STILL button to hold on the image on the screen (the video sources are still operating). Press the button again to reactivate the image. Note: For the sake of protecting the screen, please do NOT still a picture for a long time. 21 Setting Sound Adjusting the Volume Using the volume buttons (VOL+ and VOL-) Press the VOL + or VOL- to increase or decrease the volume. Using the Mute At any time, you can temporarily cut off the sound using the MUTE button. 1 2 1 2 3 4 5 Press the MUTE button and the sound cuts off. To turn mute off, press the MUTE button again. Customizing the sound Video Sound Mode Bass Treble Audio 30 30 30 User Press MENU to display the menu main page. Balance Press 5or6 repeatedly to select Audio menu. Setup Earphone Vol 30 Digital Audio Output MTS RAW Mono To Move OK To Select Exit To Exit Press OK or4 to access the submenu. Feature Within the menu, use 5, 6, 3or4 to navigate or adjust. Press OK or 4button to confirm, enter sub-menu or toggle the settings of the selected menu item. Press EXIT button to exit. Option Function Selects sound mode. Adjusts Bass (low sounds) Adjusts Treble (high sounds). (The above menu is shown as an example. It is in TV mode and the signal is analog) Choice/Range/Remarks User/News/Music/Movie Note: you may directly press SOUND MODE button on the remote control to select. [. . . ] Enter 9-9-3 and then press the mode key for the device you want to control volume (for example, TV). Now when you press VOL+, VOL-, or Mute, the selected device (for example, TV) will control the volume regardless of the current mode. Unlocking All Volume Control (Restoring Global Unlock) Press and hold SET until the red LED blinks twice; then release. Volume is now independently controlled for all programmed devices. 1. Unlocking a Single Device's Volume Control Press a device key (TV, VCR/DVD, CBL/ SAT, or AUX). [. . . ]