User manual POLAROID SPRINTSCAN 45I QUICKSTART GUIDE

[. . . ] Microsoft Windows 95, Windows 98, or Windows NT (version 4 or later) operating system. An ASPI-compliant SCSI adapter with the appropriate Windows 95 or Windows NT drivers. A video adapter and monitor capable of displaying 24-bit color (16. 7 million colors) is recommended for optimal display of scanned pictures. (PolaColor Insight software runs on systems with adapters and monitors with less color capability, but pictures displayed on the monitor may not be satisfactory. ) · · · · · You must have this free disk space available for temporary image processing. [. . . ] Do not change it unless another device is using 4. Other addresses typically available are 2, 5, and 6. 25 pins 50 pins 25 pins 50 pins Terminator You may need additional cables or adapters to connect the scanner. Your cable must have a 50-pin Centronics M or DB-25 M connector at one end for attachment to the scanner, and the cable should be as short as possible. To determine the connector you need for attachment to your SCSI adapter, refer to instructions with the adapter. Terminate the scanner and all other SCSI devices as shown in the appropriate diagram in the previous section. The last device in the SCSI chain must be terminated (or termination on), while all other devices must be unterminated (or termination off). Termination instructions for your other SCSI devices are provided with the devices. Computer Other SCSI device (unterminated) 50 pins 25 pins 50 pins Scanner 25 pins Computer Scanner Other SCSI device (terminated) English 8 English 9 5 Connect the Scanner to AC Power and Turn On 1 2 Turn on the scanner by pressing the power switch. Connect the power cord as shown. a b I I O 3 Check the lights. The yellow light blinks while the scanner initializes, remaining steady when the scanner is ready. (The green light also blinks while scanning. ) Turn on the computer. Wait for the system to install the scanner driver and display the normal desktop. 4 I O 5 c d e a b c Air intake SCSI address switch Power switch d e Power connector SCSI connectors (25, 50) 6 Loading the Film Carriers The Four-Slide Film Carrier 1 With the text facing up and the hinge at the top, open the carrier flat as shown. 3 Close the carrier carefully. The 4x5 Carrier (for 4x5 film) 1 2 Place up to four mounted 35mm slides in the spaces provided. Be sure the slide mounts fit properly in the recessed areas. The images should be right-side up and right-reading as you do so. The emulsion side will face down. To unlock the carrier, squeeze the two halves of the carrier together at the bottom edge (near the locking knob) with one hand while turning the locking knob in either direction, until the slot in the knob points to UNLOCK. CK LO UN CK LO English 10 English 2 11 Open the carrier flat. Insert a 4x5 chrome or negative so that the left edge is against the positioning pins. Position the film so the image is right-reading and right-side up (emulsionside down). Note: The emulsion side is the dull side. The 120 Film Adapters (for 2¼ x 2¼ and 2¼ x 2¾ in. film) 1 2 Open the 4x5 carrier as described previously. Locate the appropriate adapter for your image. One is designed for 2¼ x 2¾ in. images, and one is for 2¼ x 2¼ in. square images. Note: The frame of film must be cut from the film strip in order to be scanned. 3 Pins Orient the adapter so that the words THIS SIDE UP (on the adapter) face up, and the notches are at the left edge. Place the unmounted film over the opening, within the raised ridges of the adapter. Position the film so the image is rightreading and right-side up. 3 Close the carrier. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient/relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. [. . . ]