User manual POLK AUDIO ATRIUM 60

[. . . ] Paint mask (to cover unpaintable parts--not included. ) To make an easy paint mask, use the grille as a template and cut a mask from heavy, nonporous Kraft paper. Remove the grille by carefully hooking it with a bent paper clip and pulling it gently away from the cabinet [figure 4]. Mask off the binding posts on the back of the speaker [figure 5], the end panels and bracket knobs, and carefully mask off the front of the speakers to protect the drivers and baffles while painting [figure 6]. [. . . ] Always use two wall anchors and two screws per speaker [figure 10b]. Drive screws into stud or wall anchors, leaving screw heads protruding 1/8" (3 mm). Vous pouvez le faire en retirant les boutons du support de l'enceinte et en la dégageant du support, ou en laissant l'enceinte dans son support [figure 9]. FIGURE 10 Use #10 screw for wall stud, use #10 wall anchors + screw for no wall stud. Use tornillos n° 10 si la pared tiene parales internos, use anclas de pared y tornillos n° 10 si la pared no tiene parales internos. Get more information and exclusive accessories, visit www. If speaker wire is being fed from a hole in the wall behind the bracket, pull this speaker wire through the hole in the bracket before mounting the bracket [figure 11]. Line up the bracket, attached to the speaker, so that the screw heads pass through the large center hole of the bracket's keyhole slot. Let the speaker and bracket slide straight down, allowing the screw head to slip behind the smaller end of the keyhole slot [figure 12]. Tug gently on the speaker to make certain that the screws and bracket are properly aligned and that the wall anchors are secure. If the bracket is not held snug against the wall by the screw heads, remove the speaker from the wall, drive the screws in a little further and then remount the speaker. Once the speaker is mounted, the bracket knobs can be loosened to "aim" the speaker, and then hand-tightened to keep the speaker angled correctly [figure 14]. Si le fil de haut-parleur destiné à l'enceinte est passé dans le mur et sort derrière le support, passez le fil à travers le trou du support avant d'installer le support au mur [figure 11]. Carefully pry out the binding post plugs to expose banana plug holes. Product Disposal - Certain international, national and/or local laws and/or regulations may apply regarding the disposal of this product. For further detailed information, please contact the retailer where you purchased this product or the Polk Audio Importer/Distributor in your country. A listing of Polk Audio Importer/ Distributors can be found on the Polk Audio website www. Polk Audio loudspeakers and subwoofers are capable of playing at extremely high volume levels, which could cause serious or permanent hearing damage. Accepts no liability for hearing loss, bodily injury or property damage resulting from the misuse of its products. Keep these guidelines in mind and always use your own good judgment when controlling volume: · High volume in an automobile can hinder your ability to safely operate a vehicle. You are responsible for knowing the local laws governing acceptable mobile volume levels. FIGURE 11 Feed speaker wire from wall through bracket wire hole for easy mounting. [. . . ] 8 for salt and corrosion with PowerPort Plug Cabinet Material Mineral filled polypropylene Grille & Bracket Material powder coated aluminum Hardware Brass or stainless steel Terminals 1 pair Gold plated 5-way binding posts Woofer 1 6 1/2" (16. 8 for salt and corrosion» avec bouchon «Power Port Plug» Matériau du caisson Polypropylène à charge minérale Matériau de la grille et du support Aluminium enduit de poudre Quincaillerie Laiton ou acier inoxydable Bornes 1 paire de bornes «5 façons» plaquées or Woofer 1 61/2" (16, 5 cm) avec cône en polypropylène à charge minérale et suspension en butylcaoutchouc Tweeter 1" (25mm) à dôme métallisé avec structure magnétique en néodymium Hauteur x Largeur x Profondeur avec support et boutons 13 1/2" H x 7 11/16" L x 9 5/16" P (34, 2 cm H x 19, 5 cm L x 23, 6 cm P) Poids à l'expédition, la paire 26, 4 lb - 12, 0 kg Warrants to the original purchaser only that this Polk Audio Loudspeaker Product (the "Product") will be free from defects in materials and workmanship for a period of two (2) years from the date of original retail purchase from a Polk Audio Authorized Dealer. However, this Warranty will automatically terminate prior to the expiration of the two (2) years if the original retail purchaser sells or otherwise transfers the Product to any other party. the original retail purchaser shall hereinafter be referred to as "you. [. . . ]