User manual POLK AUDIO CSW100

[. . . ] Product Disposal-- Certain international, national and/or local laws and/or regulations may apply regarding the disposal of this product. For further detailed information, please contact the retailer where you purchased this product or the Polk Audio Importer/Distributor in your country. A listing of Polk Audio Importer/Distributors can be found on the Polk Audio website www. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. [. . . ] the card pre-programs equalization and overload protection. The card also has power control circuitry designed specifically to the subwoofer's requirements for extra reliability (see SWA500 instruction manual for installation instructions). important Note: The CSW100 IS NOT moisture-proof. Never allow it to come into contact with water. cSW100 INSTALLATION PROCEDURE Protective Cover A 1/2" thick protective cover of MDF covers the CSW100 grille opening. This protective cover (3 1/4" x 13") is also the template you will use to cut the grille opening. Once installed, all you see is a tiny 2" x 12" grille (optional). Patented High Velocity Compression Drive® bandpass alignment with slot bass venting-- produces a gutsy, driving bass that other similarly sized built-ins can't equal. If you choose to use another grille, use one that doesn't resonate and caulk it. Taking the dimensions of the CSW enclosure, mark off the dimensions of the enclosure and then the center line dimensions of the woofer opening. Using the protective cover/template, mark off the grille opening you wish to cut. Note: Hold the subwoofer into the floor or ceiling. You will need to support a 33 pound subwoofer during the installation, so have a co-worker or mechanical device support the woofer during final installation. (Use the 3/4" screws supplied) Tighten both brackets on one side of the subwoofer until the brackets seat flush against the subwoofer. Attach additional anti-resonance pads (included) to any sides of the subwoofer that will mount flush against support beams. Place the subwoofer in the floor or ceiling space flush with the beam face, then attach the brackets to the beam, tightening them down completely. Extend the two loose brackets that attach to the other beam and tighten them flush against the beam. Direct Radiating Slot Port enclosure--produces a gutsy, driving bass that other similarly sized built-ins can't equal. THE SWA500 AMPLIFIER AND SPEX CARDS Note: When installing the Polk Audio SWA500 matching amplifier, make sure you install the appropriate SPEX Card. THE CSW155 CARTON INCLUDES: 1 Subwoofer 4 Mounting Brackets 16--3/4" Particle Board Panhead Screws 16 Washers 11 Isolation Pads (6 installed, 5 included) 1 Registration Card 1 Owner's Manual 1 Grille The CSW155 uses a 15 1/2" x 17 1/2" grille, which is included with the subwoofer. THE SWA500 AMPLIFIER AND SPEX CARDS Note: When installing the Polk Audio SWA500 matching amplifier, make sure you install the appropriate SPEX Card. see the SWA500 Manual for installation procedure. [. . . ] , warrants, to the original retail purchaser only, that the LOUDSPEAKER(S), PASSIVE CROSSOVER COMPONENT(S) and ENCLOSURE on this Polk Audio Loudspeaker Product will be free from defects in material and workmanship for a period of five (5) years from the date of original retail purchase from a Polk Audio Authorized Dealer. , warrants, to the original retail purchaser only, that any AMPLIFIER OR OTHER ELECTRONIC COMPONENT that may be included in this Polk Audio Loudspeaker Product will be free from defects in material and workmanship for a period of three (3) years from the date of original retail purchase from a Polk Audio Authorized Dealer. To allow Polk Audio to offer the best possible warranty service, please register your new product online at: www. Com/registration or call Polk customer service 800-377-7655 in the USA and Canada (outside the USA: 410-358-3600) within ten (10) days of the date of original purchase. [. . . ]