User manual POLK AUDIO DX3065

[. . . ] dX Series Polk Audio dXSeries Dynamic Balance® Component Systems Premium Performance Loudspeakers Owner's Manual dX3055 dX3065 dX3000 dX5510 dX6510 5601 Metro Drive · Baltimore, Maryland 21215 · (800) 377-7655 http://www. polkaudio. com "Polk, " "Polk Audio, " "The Speaker Specialists" and "Dynamic Balance" are registered trademarks of Polk Investment Corporation used under license by Polk Audio Incorporated. System System Tweeter Mid/Woofer Mid/Woofer CE RM0466-1 Polk Audio--A History of Excellence Polk Audio was founded in 1972 by Matthew Polk and George Klopfer. Their dream was to make speakers with the performance of the world's best speakers, at a reasonable price. They did so by applying scientific principles to speaker design and by concentrating solely on the speaker business. That is how Polk became known as "The Speaker Specialists. " Today Polk Audio is still headquartered in Baltimore, Maryland, and is now one of the world's largest manufacturers of home and car loudspeakers. [. . . ] Pay particular attention to window mechanisms and any body panels critical to the structural integrity of the vehicle. The mounting depths and cutout diameters of your dX Series mid/woofers are listed with all the other important specifications at the end of this manual. TWEETER WOOFER INPUT FIG. 1 (Note: Crossover is not weather proof) dX Series dX Series 8 Premium Performance Loudspeakers Premium Performance Loudspeakers 9 1. The grilles supplied with the dX Series drivers can be used as a tem plate for marking the cutout holes. Using the speaker grille as a template for marking the locations of the four screw holes. Attach the screw clips to the car panel at the hole locations. Attach speaker wires to the crossover "woofer" terminals. Attach the wire with the white stripe to the positive (+) terminal screw, and the un-striped wire to the negative (-) terminal screw. Using a crimping tool, attach faston connectors to the speaker end of each of the wires going from the crossover to the mid/woofer. Remove the mesh grille from the grille frame and pass the wire through the grille frame. Slip the faston connectors onto the input terminals on the mid/woofers. Be sure to attach the wire with the white stripe to the positive (+) terminal, and the un-striped wire to the negative (-) terminal. Place the speaker into the grille frame and line up the screw holes with the screw clips on the car panel. Secure the speaker/grille frame assembly to the car panel with the supplied screws. Place the mesh grille in the grille frame. dX System Tweeters One important advantage of component systems is their ability, when properly installed, to improve the soundstage created by the music in your car. The soundstage is the musical "picture" made up of the instruments and vocalists. The difference in the soundstage will be dramatic depending on where you mount your tweeters. We recommend a simple experiment that will help you decide the best spot for your tweeters in your car. Mark the center of the hole and cut a 2. 1 inch hole with razor knife or reciprocating saw. dX Series 10 Premium Performance Loudspeakers Premium Performance Loudspeakers 11 4. Insert front half of flush cup into the hole and manually push clamp ring (Figure 3) on until cup is tight on front surface. Put tweeter in bottom half of flush cup and twist lock to front half of assembly created in step 4. [. . . ] Authorized Polk Audio dealers are the best source for advice and assistance. Call Polk Audio's Customer Service Department at 1-800-377-7655 from 9am to 6pm, Eastern Time, Monday through Friday. Please do not hesitate to call us if you have questions about your speaker system. dX3055 comprised of dX5510 and dX3000 dX3065 comprised of dX6510 and dX3000 Specifications db4510 Recommended Amplification Impedance(DCR) Frequency Response (+/-3dB) Sensitivity (1w/1m) Magnet Weight Mounting Depth top mount Mounting Depth top mount w/out grille Mounting Depth top mount with grille Mounting Depth bottom mount Grille Height Grille Diameter Crossover Frequency Crossover Order dX5510 5-100 watts 4. 0 ohms 60 Hz-5. 5 kHz 86 dB dX6510 5-100 watts 4. 0 ohms 45 Hz-4. 5 kHz 85 dB dX3000 5-100 watts 4. 0 ohms 2 kHz-20 kHz "+3dB" - 87 dB* " 0dB" - 84 dB "- 3dB" - 81 dB 5 oz 1" flush mount 1. 315" surface mount height N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 4800 Hz B =1st Order Butterworth A =2nd Order Butterworth 13. 5 oz N/A N/A 2 9/16" 65. 1 mm 2 7/16" 61. 9 mm 2 3/4" 69. 9 mm 7/8" 22. 2 mm 6 1/4" 159 mm B=3800 Hz A=3800 Hz B = 1st Order Butterworth A = 2nd Order Butterworth 13. 5 oz N/A N/A 2 3/4" 69. 9 mm 2 5/8" 66. 7 mm 3" 76. 2 mm 15/16" 23. 5 mm 7 3/16" 183 mm B=3800 Hz A=3800 Hz B = 1st Order Butterworth A = 2nd Order Butterworth *When dX3000 bought separately sensitivity = 90 dB with loop intact/3400 Hz When dX3000 bought separately sensitivity = 87 dB with loop cut/3400 Hz dX Series dX Series 16 Premium Performance Loudspeakers Premium Performance Loudspeakers 17 Dynamic Balance® Series Mid/Woofer Technical Sheet THEILE / SMALL PARAMETERS Freq. (Fo, Fs) Qms Qes Qts Vas Cms BL Sd Mms Winding Width Xmax (Linear) Xmax (Mechanical) Le dX5510 60Hz-5. 5kHz 72 Hz 5. 46 0. 68 0. 61 4. 34L . 153 ft3 329 µm/N 5. 73 TM . 0097m2 . 1040ft2 14. 1 g 12. 7mm . 500in. [. . . ]