User manual POLK AUDIO FX1000

[. . . ] This total, integrated system is called the RT5000. All the drivers and tweeters in this system are identical, ensuring perfect channel to channel timbre matching for absolutely seamless imaging as well as extremely high definition and extraordinary dynamic range. Notify your Polk dealer if you notice any damage. They will do the best job of protecting your speakers if they need to be transported. [. . . ] Each (not supplied) into the wall by following wall anchor manufacturer's instructions. Always use two wall anchors and screws per speaker. Lift the speaker and locate so that both screw heads pass through the large center hole of the keyhole slots. Let speaker slide straight down, allowing screw heads to slip behind the smaller end of the keyhole slots. Push the speaker gently along the bottom and top side, to insure that both keyhole brackets are engaged. Use cinta o tachuelas para fijar la plantilla; use nivel de burbuja o plomo para cerciorarse de que la plantilla esté nivelada. Measure enough wire to reach from your receiver or amp to each speaker. Keep in mind the extra length needed for running the wire around doors. Leave yourself about 12" of extra slack to allow moving the speakers or receiver without having to disconnect the wires. note that one of the terminals on the rear of the speaker is marked red (+) and the other black (). Make certain that you connect the wire from the red (+) terminal of your amplifier to the red (+) terminal on your speaker, and the wire from the black (-) terminal of the amplifier to the black (-) terminal on your speaker (Figure 5). Most wire has some indication (such as color coding, ribbing, or writing) on one of the two conductors to help maintain consistency. Strip 1/2" of insulation from each of the two conductors on both ends to expose the bare wire. Twist the exposed wire of each conductor to form two unfrayed strands. Connect two conductors to the receiver or amp (refer to the owner's manual supplied with your electronics for assistance with proper hookup). Use either input when jumper bars are in place Use either input when jumper bars are in place Use with amplifiers rated from 20 to 500 watts per channel. Use with amplifiers rated from 20 to 500 watts per channel. Your speakers will work well with a variety of electronic components. As little as 20 watts per channel will deliver adequate listening levels in most rooms. If you have a large room or intend to play your system at loud listening levels, more power is necessary to achieve the best performance. UTILISATION DES BORNIERS "CINQ FAÇONS" Loosen hex nut GEBRAUCH VON FÜNFERVERBINDUNGSBOLZEN Desenrosque parcialmente la tuerca hexagonal Desserrer l'écrou Sechskantmutter lösen Insert speaker wire through hole Inserte el alambre para la bocina en el orificio Insérer le fil du haut-parleur dans le trou Lautsprecher-Draht durch das Loch schieben Tighten hex nut Enrosque la tuerca de nuevo Serrer l'écrou Sechskantmutter festschrauben Do not insert insulated section of speaker wire No inserte alambre con material aislante Ne pas insérer la partie isolée du fil du haut-parleur Isolation des LautsprecherDrahtes nicht in das Loch schieben You can achieve performance advantages by either bi-wiring or bi-amplifying your f/x1000's. To many people these improvements are subtle, to others they are significant. [. . . ] Driver Complement: 2x 1"(25mm) Dynamic Balance® dome tweeters 2x 6 1/2"(165mm) Dynamic Balance drivers Overall Frequency Response: 40Hz - 26kHz -3dB Limits: 50Hz - 25kHz Crossover Topology: 2nd Order Low Pass Filter @2 kHz 2nd Order High Pass Filter @2 kHz Mylar film capacitors used throughout Impedance: compatible with 8 ohm outputs Recommended Amplification: 20 - 250 WRMS Efficiency (1M, 1Watt): 90dB Available Finishes: Black or Rosewood Finish Wood Veneer Dimensions: 11 1/4"W x 19 13/16"H x 9 3/4"D 28. Warrants to the original purchaser only that this Polk Audio Loudspeaker Product (the "Product") will be free from defects in materials and workmanship for a period of five (5) years from the date of original retail purchase from a Polk Audio Authorized Dealer. However, this Warranty will automatically terminate prior to the expiration of the five (5) years if the original retail purchaser sells or otherwise transfers the Product to any other party. the original retail purchaser shall hereinafter be referred to as "you. [. . . ]