User manual POLTI COSMO

[. . . ] You can decide, depending on your needs, whether to use the steam and suction together for complete cleaning, just the suction to effectively collect dust or just the steam for specific cleaning tasks. The suction feature: The heart of the filtration system is represented by the exclusive "Eco-Active" water filter, patented by Polti. The "Eco-Active" water filter uses the natural purifying force of water to trap dirt, preventing dispersion of dust into the environment. In addition, the HEPA filter collects impurities including pollen as well as dust mites. [. . . ] The two bristle inserts (4A) must be inserted by positioning the full one on the rear part of the brush, while the one with openings goes in the front. The liquid suction inserts (4B) must be inserted paying attention that their smooth side is facing the inside of the brush. C1 To assemble the inserts on the steam-suction nozzle (6): To assemble the insert, 6A or 6B, insert it and slide it onto the nozzle (fig. D). ENGLISH 116 COSMO A - ORDINARY CLEANING A1) HARD FLOORS (MARBLE, GRANITE, TILE) ACCESSORIES TO BE USED: extension tubes (2)(3), universal brush (4) with inserts, as per the following table: ACCESSORIES REFERENCE LETTER PHOTOGRAPH + + FUNCTION Extension tubes + universal brush + 2 + 3 +4 + 4A bristle insert Extension tubes + universal brush + 2 + 3 +4 + 4B rubber insert Vacuuming dust + + Liquid aspiration; steam flow and floor drying VACUUM FUNCTION vacuum up dust and liquids or effectively remove animal hair Press the suction switch (A) to begin vacuuming. Regulate the suction regulator (1D) to maximum power to vacuum up dust or liquid (see paragraph entitled Vacuum only function). To stop suction, simple press the switch (A). STEAM AND VACUUM FUNCTION Wash and vacuum even the dirtiest floors. This function enables the sanitisation of all types of hard flooring, such as marble, granite and ceramic. Before steaming surfaces, we recommend vacuuming up any hair or dust, using the vacuum only function. After having turned the boiler on, following the instructions given in the paragraph entitled "Operation", set steam pressure according to how dirty the surface to be treated is (see paragraph entitled Steam flow regulation). Press the button (1C) on the handle to dispense steam over the surface to be cleaned. To stop steam flow, simply release the button (1C). Then activate the vacuum function by means of the switch (A) to dry the surface treated. In the case of old or particularly delicate floors, clean with cloth steamed previously, without dispensing steam directly on the surface. ACCESSORIES TO BE USED: extension tubes (2)(3), universal brush (4) with inserts, as per the following table: ACCESSORIES Extension tubes + universal brush + rubber insert REFERENCE LETTER 2 + 3 +4 + 4B PHOTOGRAPH + + + + + + + Vacuuming dust Steam delivery FUNCTION Vacuuming liquids Extension tubes + 2 + 3 +4 + 4C + universal brush + O2 rigid insert + cloth Extension tubes + universal brush + 2 + 3 +4 + 4A bristle insert ENGLISH 120 COSMO PARQUET AND TERRACOTTA VACUUM FUNCTION To vacuum up dirt and dust on parquet/terracotta Press the suction switch (A) to begin vacuuming. Regulate the suction regulator (1D) to vacuum up dust or liquid (see paragraph entitled Vacuum only function). To stop suction, simple press the switch (A). STEAM-VACUUM FUNCTION To wash the parquet/terracotta N. B. To prevent steam temperature or pressure from damaging the parquet/terracotta, use the brush with the inserts, always wrapping it in a cloth. We recommend alternating steam delivery with the activation of the suction function, in order to avoid leaving the parquet/terracotta damp for long periods of time. The steam and suction functions can also be used simultaneously. After having turned the boiler on, following the instructions given in the paragraph entitled "Operation", set steam pressure according to how dirty the surface to be treated is (see paragraph entitled Steam flow regulation). Press the button (1C) on the handle to dispense steam over the surface to be cleaned. To stop steam flow, simply release the button (1C). Then activate the vacuum function by means of the switch (A) to dry the surface treated. [. . . ] · Lift the HEPA filter release lever (U) and remove the filter (T) from its housing (Fig. 12). · Rinse the filter under cold running water. · After washing it, shake it gently to eliminate any reside of dirt and excess water. NOTE: allow the filter to dry naturally, away from direct sources of light and heat. [. . . ]