User manual POLTI LECOLOGICO SPECIALE PARQUET

[. . . ] 16 B 17 C C1 W 9 9a Fig. 20 E F L G H 17b 16 17a 10 17c N M Fig. 24 O P1 P Z X 6 LECOLOGICO SPECIAL PARQUET KEY 1) Main switch 2) Cable winder button 3) Carry handle 4) Container handle 5) Rear wheels 6) "EcoActive-Filter" water container 7) MAX level (fig. 4) 8) Air outlet grid 9) Filter cover (fig. 16) 9a) Filter cover opening levers (fig. 16) 10) Hepa filter (fig. 18) 10a) Hepa filter retainer (fig. 17) 10b) "Dual filter" assembly (fig. 17) 11) Accessories holder housing 12) Casters 13) Power cable plug 14) Indicator lights 15) Connection 16) "Eco Active Filter" water filter assembly 17) Filter cage cover 17a) Filter cage body with fine mesh 17b) Sponge filter 17c) Filter nozzle 18) On/off and increased suction power button 19) Decreased suction power button KEY TO ACCESSORIES A) Telescopic tube A1) Telescopic tube release button B) Joker brush C) Universal brush C1) Brush selector D) Hose D1) Suction opening E) Multipurpose nozzle F) Lance for cleaning corners / skirting boards G) Soft brush H) Accessories holder hook L) Radiator brush M) Jointed tube N) Mini turbo brush O) Parquet brush P) Wheel covers for hardwood floors P1) Wheel covers anchoring joints W) Float X) HP007 Z) Water container cleaning brush 34 LECOLOGICO SPECIAL PARQUET Dear Customer, We would like to thank you for choosing this Polti appliance. By choosing Lecologico, you have made a healthy choice for your home. [. . . ] Fill the water container (6) with ordinary tap water up to the MAX H2O indicator (7) as shown in figure 4. The required quantity is 800cc of water. Place the filter assembly (16) in the water container (6), being careful to align them perfectly. Put the water container (6) back inside the appliance, performing the operations listed above in reverse order. Insert the suction opening (D1) on the hose (D) into connection (15) (fig. FUNCTIONING Unwind the cable (13) to remove it COMPLETELY from its housing, pulling the plug towards you (fig. 8) and the first level of the indicator lights (14) will begin flashing. This means Lecologico is in the pause position. Hold down the button (18) for more than one second, then release it. Lecologico will begin operating at minimum speed, and the first indicator light (14) will stay on. We recommend minimum power for curtains, medium/low power for sofas, armchairs and cushions, medium/high for carpets and high for floors and hard surfaces (ceramics, marble, etc. ). Press button (18) to increase speed; each time you press button (18), the motor power increases by one step. At each speed increase a further level of the indicator lights come on. Press button (19) to decrease speed; at each speed decrease a further level of the indicator lights goes out. To restore the appliance to the pause position, hold down button (18) for more than one second, then release it. · · · · · · · The user is responsible for delivering the appliance to an appropriate collection facility at the end of its useful lifespan. Appropriate separate collection to permit recycling, treatment and environmentally compatible disposal helps prevent negative impact on the environment and human health and promotes recycling of the materials making up the product. For more information on available collection facilities, contact your local waste collection service or the shop where you bought this appliance. I N S TA L L AT I O N Before using Lecologico, assemble the casters (12) as shown in figure 1. · · · D RY ­ L I Q U I D S U C T I O N The appliance can be used in the same way to vacuum up dust or limited amount of liquids. If the water is very dirty, replace it as described in 37 LECOLOGICO SPECIAL PARQUET the section on "Emptying and cleaning the water container". When the dirt collected in the water container (6) reaches the maximum permitted level, the safety float (W) will automatically stop the suction. The motor will turn over audibly faster. After 10 seconds the appliance will automatically pause and the four indicator lights (14) will start flashing. [. . . ] Let the sponge filter dry before putting it back into the appliance. · Reassemble the filter assembly, repeating the operations in the reverse order. Note: Make sure that the filter nozzle (17c) is correctly positioned, checking that the arrow on the nozzle is aligned with the notch on the bottom of the cage (17a) (fig. 15). · If the filter needs replacing, always use an original filter, available from Polti Technical Service Centres. [. . . ]