User manual POLTI MONDIAL VAP 2000 SUPER POWER NO VOLT

[. . . ] R A I 2 3 G N 2A L 5 K 6 U R S 4 1 J F D B T C Q E H 5 11 6 4 11 21 12 7 11 9 8 10 15 9 14 9 11 22 23 13 11 16 16 11 18 19 24 11 17 20 ENGLISH ® A) B) C) D) E) F) G) H) I) J) K) L) N) GENERATOR Patented Safety Cap Main Generator on/off switch Accessory on/off switch Central connector block Lock-in aperture for central connector Power supply cable Carrying handle Rotating wheel Steam regulation control "Water out" indicator light "Pressure building" indicator light Pressure gauge Water level indicator ACCESSORIES Flexible hose Steam gun Safety switch Steam request lever Connector assembly Press down connector button Locking tab Extension tubes Large brush Cloth retaining clips Replaceable bristles plate Accessories locking button Small brush Cotton cloths Filler bottle 15) Spare washers for accessory connections 16) 120° nozzle 17) Small round brush for 120° nozzle 18) Window squeegee tool 19) Small blade for window tool 20) Large blade for window tool 21) High pressure lance ACCESSORIES SOLD SEPARATELY Iron Steam request button Temperature regulation control Iron rest Continuous steam jet button Triangular brush Large round brush for 120° nozzle Wallpaper stripper tool 1) 2) 2A) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) Q) R) S) T) U) 22) 23) 24) TECHNICAL DATA Power supply Resistance (generator) 230 V ~ 50 Hz 2200W (1500+auxiliary 700) Resistance of Iron (optional) 750W Generator capacity 3l Polti S. p. A. reserves the right to change equipment or accessory specification without prior notice. This unit conforms with EC-directives 89/336 as amended by 93/68 (EMC) and 73/23 as amended by 93/68 (low voltage). ENGLISH FOR YOUR OWN SAFETY READ FOLLOWING INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO CONNECT THIS UNIT TO THE MAINS. M A I N S ( A C ) O P E R AT I O N This unit is designed to operate on 240V, 50 Hz current only. Connecting it to other power sources may damage the unit. WARNING - This appliance must be earthed. [. . . ] Check that the connector button has engaged and the accessory is fully connected. Fig. 6 ENGLISH PAT E N T E D S A F E T Y C A P / ' WAT E R O U T ' All POLTI machines are equipped with the unique Polti patented safety cap, which prevents opening of the generator tank as long as there is any pressure remaining inside the tank. This is an important and indispensable safety device, and it is necessary to follow certain procedures when re-filling the tank. According to model, `water out' is indicated by a warning light (J), or by an audible alarm signal from the machine, or on more basic models by the exhaustion of the steam output. Whenever you have used up all the water in the tank, follow the following procedures: 1c. Switch off the machine at the generator on/off switch (B) 2c. Press the steam request lever (3) on the hand gun (2) or, if using the iron, the steam request button (R) on the iron (Q) so as to fully exhaust the steam supply from the tank. Disconnect the power supply cable (F) from the mains. Unscrew anti-clockwise the patented safety cap (A) 5c. Wait 3 to 4 minutes to allow the generator tank to cool down. When cool proceed to carefully refill the tank as described in paragraph 1 of the section "Preparation for Use" in the instructions. If refilling the generator when not completely cooled, we recommend that you carefully pour only very small quantities of water at each pouring into the tank, so as to avoid spitting from the tank and cover exposed skin whilst filling. USE OF THE PROFESSIONAL STRENGTH PRESSING IRON (normally sold separately) 1d. Connect the connector block at the end of the iron hose (4) to the generator as shown in point 2A of the section "Instruction for Use". For all steam ironing, position the temperature indicator dial (F) to the position "COTONE - LINO". For dry ironing set the temperature control dial according to the fabric to be ironed as indicated on the dial. Wait three to four minutes for the indicator (R) to go out indicating that the sole plate of the iron has reached the correct temperature. Press the steam request button on the iron (R) to allow the steam to exit. Releasing this button stops the steam flow. At first you may find that the steam contains some water globules and we recommend that the first jet of steam is therefore played onto an old cloth, and is not directed onto the garment to be ironed. For dry ironing do not press the steam request button (R). In order to have a continuous steam jet, move the button (U) forwards. Steam will keep on coming out, even if you release the button. [. . . ] 120° STEAM NOZZLE (16) The 120° nozzle (which can be connected directly to the gun or together with the extension tubes) allows you to concentrate a powerful jet of steam to otherwise inaccessible locations, such as radiators, door posts, sills and shutters, as well as for sterilising toilet bowls. WINDOW SQUEEGEE TOOL (18, 19, 20) The Window Squeegee Tool allows you to clean effectively and rapidly all glass surfaces without using detergents. Your glass wilI remain cleaner longer thanks to the absence of layers of film normally left behind by chemical cleaning products on which new dust and grease can attach itself. ENGLISH Cleaning glass is done in two stages: - Spraying the steam onto the surface to be cleaned to loosen the dirt (not touching with blade). - Pulling the blade straight down the window surface from top to bottom without applying the steam, to take away the dirt. [. . . ]