User manual POLTI VAPORELLA PRATICA

[. . . ] Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 13a Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 17 Fig. 18 Fig. 19 Fig. 20 Fig. 21 Fig. 22 Fig. A Fig. B 1 16 65 4 3 2 9 A 12 13 B 15 10a 10b 10 14 7 24 11 D 18 10 8 VL Pratica - -Pratica Basic M0S07292 2P10 17 8 10 C 17 20 23 21 22 19 VAPORELLA PRATICA - PRATICA BASIC Dear Customer, We would like to thank you for your confidence in choosing a Polti product. Vaporella Pratica is specially designed for fabrics: it will help you in ironing, spotting, refreshing and eliminating smells. Vaporella Pratica can also be used to clean and sanitise small surfaces in your house using just the power of steam. Thanks to its wide range of accessories, Vaporella Pratica can be used for many different jobs, thanks to its trolley it can follow you wherever you need. [. . . ] Connect the chosen accessory for the required job to the generator, as described in the paragraph "ACCESSORIES CONNECTION" WARNING: Do NOT under any circumstances put or leave the funnel in the water filling aperture of the appliance when the appliance is connected to the mains electricity supply. ACCESSORIES CONNECTION All Vaporella accessories can be connected to the generator (A) as described below: · Open the cover of the built-in socket (16) (fig. A). · Insert the one-piece plug (17) (fig. B). STEAM IRONING 1b. For STEAM ironing, turn the dial (7) and set the iron to its MAXIMUM travel on the "COTTON - LINEN" steam position (fig. 7). NB Set at its maximum, do NOT set against the picture of iron on the dial (7). Most fabric types, other than delicates can be STEAM-ironed at this temperature, please consult the garment label. If you want to DRY iron, set the dial (7) to the required temperature for the fabric as shown on the dial. Nb fabric indications on the dial are for DRY ironing, for STEAM ironing set at maximum travel as explained above. NOTE: before starting ironing, make sure that the iron is hot enough by checking that the light on the iron handle has gone out (10b). NOTE: On first usage, be sure that the continuos steam jet button (10a) is not set on. Wait for the pressure indicator light (5) to go out (about 15 minutes). Push the steam request button (10) on the iron to release bursts of steam from the holes on the soleplate. DRY IRONING If you need to DRY iron (ONLY) (NOT steam ironing), press the accessory switch (3) and adjust the iron temperature by turning the dial (7) to the temperature required for the fabric (as shown on the dial). NOTE: · The steam pressure indicator (5) and the "Iron Heating" indicator (10b) may go on and off from time to time during use of Vaporella. This means the machine is maintaining the correct and constant pressure and is quite normal. · If no steam is released from the iron, check the following: the steam pressure indicator (5) is off; there is water in the boiler; the steam control (6) is set to one of the "Steam" settings. U S I N G T H E S TA I N R E M O V E R G U N (optional mod. BASIC) Before using the stain remover gun, it is advisable to carefully read the following instructions which allow a correct classification of stains and supply accurate advice on the most appropriate way of operating. I D E N T I F Y I N G T H E S TA I N In order to act properly on stains, it is important to be able to distinguish them. Identifying the stain means understanding its origin and age. This allows you to avoid unsuccessful attempts which often, as well as not producing an optimal result, can also be damaging. "THE AGE" All RECENT stains can be removed with the stain remover gun without having to wash the item. As they get older, stains attach themselves to the fabric's fibres and in some cases, steam cannot remove them. In such cases it is necessary to wash the item. If the recently stained fabrics are treated immediately with mineral water, the stain does not attach itself to the fibres and subsequent steam cleaning with the stain remover gun will prove quicker and more effective. [. . . ] Disconnect the power supply cable from the mains. Unscrew anti-clockwise the patented safety cap (1). Wait for a few minutes to allow the boiler to cool down. When cool, proceed to carefully refill the boiler as described in paragraph 3a of the section "PREPARATION FOR USE" in the instructions. [. . . ]