User manual POLTI VAPORELLA PROF 306

[. . . ] Never empty Vaporella when the water inside the generator tank is still hot. Do not place the appliance in water or in any other liquids. Do not touch the appliance with wet hands or feet whilst the appliance is connected to the mains. Never leave the appliance unattended whilst it is con2 4 2 8 7 Fig. [. . . ] For dry ironing: · Plug the cable in. · Press the iron switch (4), leaving the boiler button off (2). · Adjust the soleplate temperature turning the knob (1) setting to the temperature required according to the type of fabric. · · · · · · · · · · I M P O R TA N T Before leaving our factory all our products are rigorously tested. However, your VAPORELLA may contain some residual water in the boiler. PAT E N T E D S A F E T Y C A P / " WAT E R O U T " All Polti machines are equipped with the unique Polti patented safety cap, which prevents opening of the generator tank as long as there is any pressure remaining inside the tank. This is an important and indispensable safety device, and it is necessary to follow certain procedures when re-filling the tank. When you have used up all the water in the tank, do as follows: 1d. Switch off the boiler on/off switch (2). Press the steam request button on the iron (3) so as to fully exhaust the steam supply from the tank. Disconnect the power supply cable from the mains. Unscrew anti-clockwise the patented safety cap (5). Wait for a few minutes to allow the generator tank to cool down. When cool, proceed to carefully refill the tank as described in paragraph 1a of the section "PREPARATION FOR USE" in the instructions. If refilling the generator when not completely cooled, we recommend that you carefully pour only very small quantities of water at each pouring into the tank, so as to avoid spitting from the tank. P R E PA R AT I O N F O R U S E 1a. Unscrew the patented safety cap (5) and fill the boiler with about 0. 9 litres of water using the special funnel (9) making sure that it does not overflow (fig. However, as hard water by its nature contains limestone, which may cause a build-up of limescale in the tank, in hard water areas we recommend the use of our natural-base decalcifier KALSTOP FP 2003. Ensure the patented safety cap is fully and correctly screwed on, otherwise you may experience steam escaping from around the cap. Connect the power supply cable into an earthed power supply of the correct voltage. Switch on the boiler and iron by pressing the switches (2) and (3). The pressure indicator light (3b) will light up (fig. NOTE: during the filling operation, be careful that the water does not overflow as it may come out and wet the surface where Vaporella is laid. 3 ENGLISH VA P O R E L L A P R O F 3 0 6 I M P O R TA N T · · Do not leave the iron unattended whilst connected to the mains. Iron only on heat resistant surfaces and on surfaces that allow the steam to escape e. Ensure the patented safety cap is fully and correctly screwed on, otherwise you may experience steam escaping from around the cap. [. . . ] However, as hard water by its nature contains limestone, which may cause a build-up of limescale in the tank, in hard water areas we recommend the use of our natural-base decalcifier KALSTOP FP 2003. To clean the body of the appliance, simply use a moist cloth. Do not use solvents or detergents which may harm the body material. BLUE (Neutral) BROWN (Live) · · IMPORTANT This wires in this mains lead are coloured in accordance with the following code. · Green-and-yellow: Earth · Blue: Neutral · Brown: Live As the colours of the wires in the mains leads of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter "E" or by the earth symbol or green-and-yellow. [. . . ]