User manual POLTI VAPORETTO 2400

[. . . ] L G C B I A 5 2 2A 6 4 1 3 K J URS V D M H F T 6 E Q 5 4 11 7 11 12 15 9 11 9 23 11 21 13 14 11 8 16 10 11 11 18 19 11 24 9 20 17 22 Fig. M0S08636 - Edizione 1P03 VAPORETTO 2400 Read these instructions carefully before using the appliance. Dear Customer, Congratulations and thank you for purchasing this POLTI product, contributing to the conservation of our most precious natural resource: the Environment. VAPORETTO solves all cleaning and hygiene problems without the use of detergents - all that's needed is just normal tap water which our system transforms into steam at a constant powerful pressure, allowing you to clean more thoroughly and in an ecological way. Our Technical Development team have added a range of sophisticated improvements to make cleaning tasks both safer and more effective: · The new handle is smaller, lighter, easier to handle and more comfortable to use because you can start producing steam with just one finger, by lightly pressing a button. [. . . ] Make sure the patented safety cap (A) is fully and correctly screwed on, otherwise you may experience steam escaping from around the cap. Connect the power supply cable (F) into an earthed power supply of the correct voltage. WARNING: Do NOT under any circumstances put or leave the filler bottle in the water filling aperture of the appliance when the appliance is connected to the mains electricity supply. Press down the generator on/off switch (B) and the accessories on/off switch (C) wich will light up together with the pressure indicator light (K). Open the cover of the central connector block (D) and insert the central connector (4) pressing the connector button (5) and taking care that the locking tab (6) is correctly positioned in the lock-in aperture (E) on the block (Fig. Check that the connector button has engaged and the accessory is fully connected. P R E S S U R E I N D I C AT O R Vaporetto is equipped with an indicator (L) displaying operating pressure. PAT E N T E D S A F E T Y C A P / WAT E R O U T The appliance is equipped with a safety cap, which prevents opening of the generator as long as there is any pressure remaining inside. This is an important and indispensable safety device, and it is necessary to follow certain procedures when re-filling the tank. According to model, `water out' is indicated by a warning light (J). Whenever you have used up all the water in the tank, follow the following procedures: 1c. Switch off the machine at the generator on/off switch (B) 2c. Press the steam request lever (3) on the steam gun (2) or, if using the iron, the steam request button (R) on the iron (Q) so as to fully exhaust the steam supply from the tank. Switch OFF the accessory on/off switch (C). Disconnect the power supply cable (F) from the mains. Unscrew anti-clockwise the patented safety cap (A) 6c. Wait for a few minutes to allow the generator tank to cool down. When cool, proceed to carefully refill the tank as described in paragraph 1 of the section "Preparation for Use". If refilling the generator when not completely cooled, we recommend that you carefully pour only very small quantities of water at each pouring into the tank, so as to avoid spitting from the tank and cover exposed skin and face whilst filling. USE OF THE PROFESSIONAL IRON (optional accessory) 1d. Connect the connector assembly at the end of the iron hose (4) to the generator as shown in point 2a of the section "Instructions for Use". Check the manufacturer's label on the garment, and interpret the symbol on the label as follows: Steam ironing allowed For dry ironing, set thermostat on ··· Steam ironing allowed For dry ironing, set thermostat on ·· Check the fabric's resistance to steam ironing or dry iron with thermostat set on · - do not iron - steam ironing or treatment not allowed STEAM IRONING 2d. [. . . ] The small brush can be connected directly to the steam gun or to the extension tubes. The small brush can be used on: · furnishing fabrics (after testing on small parts) · velvets and leather (not too close) · car linings, car windows · small window surfaces · tile and other small surfaces To clean wood ( doorposts , floors etc) do not apply the steam directly but cover the brush (big or small) with a doubled cotton cloth. For furniture cleaning, direct the steam jet onto a dry cotton cloth, and then start the cleaning. The warm moisture on the cloth traps the dust, spots and the static electricity so that the furniture stays clean longer. [. . . ]