User manual POLTI VAPORETTO CLEAN

[. . . ] R R G O A L B I C D F E H 7 11 9 11 9 11 12 15 8 10 13 14 2 11 3 5 2A 1 9 22 23 6 4 16 16 11 11 24 17 18 11 19 UR S Q 20 T 11 5 21 6 4 « Fig. 5 ­ + Bild 7 Bild 8 Bild 9 Bild 10 « « « « ON F OF « « ENGLISH A) B) C) D) E) F) G) H) I) L) O) GENERATOR Patented Safety Cap Main Generator on/off switch Accessory on/off switch Central connector block with splash proof cover Lock-in aperture for central connector Power supply cable Carrying handle Pivotting wheel Steam regulation control Pressure gauge Storage for small accessories ACCESSORIES 1) Flexible hose 2) Steam gun 2A) Safety switch 3) Steam request lever 4) Connector assembly 5) Press down connector button 6) Locking tab 7) Extension tubes 8) Large brush 9) Cloth retaining clips 10) Replaceable bristles plate 11) Accessories locking button 12) Small brush 13) Cotton cloths 14) Filler bottle 15) Spare washers for accessory connections 16) 120° nozzle 17) Small round brush for 120° nozzle 18) Window squeegee tool 19) Small blade for window tool 20) Large blade for window tool ACCESSORIES SOLD SEPARATELY Q) Iron R) Steam request button S) Temperature regulation control T) Iron rest U) Continuous steam jet button 21) High pressure lance 22) Triangular brush 23) Large round brush for 120° nozzle 24) Wallpaper stripper tool Polti S. p. A. reserves the right to change equipment or accessory specification without prior notice. FOR YOUR OWN SAFETY READ FOLLOWING INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO CONNECT THIS UNIT TO THE MAINS. M A I N S ( A C ) O P E R AT I O N This unit is designed to operate on 240V, 50 Hz current only. Connecting it to other power sources may damage the unit. [. . . ] Switch off the machine at the generator on/off switch (B) 2c. Press the steam request lever (3) on the hand gun (2) or, if using the iron, the steam request button (R) on the iron (Q) so as to fully exhaust the steam supply from the tank. Disconnect the power supply cable (F) from the mains. Unscrew anti-clockwise the patented safety cap (A) 5c. Wait 3 to 4 minutes to allow the generator tank to cool down. When cool proceed to carefully refill the tank as described in paragraph 1 of the section "Preparation for Use" in the instructions. If refilling the generator when not completely cooled, we recommend that you carefully pour only very small quantities of water at each pouring into the tank, so as to avoid spitting from the tank and cover exposed skin whilst filling. USE OF THE PROFESSIONAL STRENGTH PRESSING IRON (normally sold separately) 1d. Connect the connector block at the end of the iron hose (4) to the generator as shown in point 2a of the section "Instruction for Use". For all steam ironing, position the temperature indicator dial (F) to the position "COTONE - LINO". For dry ironing set the temperature control dial according to the fabric to be ironed as indicated on the dial. Wait three to four minutes for the indicator (R) to go out indicating that the sole plate of the iron has reached the correct temperature. Press the steam request button on the iron (R) to allow the steam to exit. Releasing this button stops the steam flow. At first you may find that the steam contains some water globules and we recommend that the first jet of steam is therefore played onto an old cloth, and is not directed onto the garment to be ironed. For dry ironing do not press the steam request button (R). In order to have a continuous steam jet, move the button (U) forwards. Steam will keep on coming out, even if you release the button. To interrupt the outlet, move the button (U) backwards. 6d. The iron can also be used in a vertical position e. g. for removing creases from curtain, clothing etc. IMPORTANT · Do not leave the iron unattended whilst connected to the mains. · Iron only on heat resistant surfaces and on surfaces that allow the steam to escape e. g. [. . . ] · Apply a little Vaseline to the cap thread every 4-5 months to prevent sticking. · We recommend that the bristles of the brushes are allowed to cool down in their normal position after use, so as to avoid any mis-shaping. · Check periodically the condition of the coloured washer connections on the the central connector (4). If necessary, replace the washers with the spare washers supplied (15). [. . . ]