User manual POLTI VTT.1000

[. . . ] · Green-and-yellow: Earth · Blue: Neutral · Brown: Live As the colours of the wires in the mains leads of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter "E" or by the earth symbol or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter "N" or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter "L" or coloured red. PLEASE READ THE FOLLOWING BEFORE USE · · Before using your VAPORETTO carefully read these usage instructions. Before connecting VAPORETTO to the mains make sure that the current is the same as that indicated for the machine and that the plug is an earthed plug. [. . . ] The first burst of steam may contain some water droplets, due to imperfect thermic stabilisation inside the flexible hose. We would therefore advise that the first jet of steam is played onto an old cloth until a constant pressure of steam is obtained. Should the hose be submitted to an excessive torsion during use flow, the No-Volt device will stop the steam flux. In order to restore the output, just press the steam request lever. Note: The on/off switch (B) may go on and off from time to time during use of VAPORETTO. This indicates the machine maintaining the correct and constant pressure and is quite normal. · · · · · · · · · · CONNECTION OF ACCESSORIES To connect the accessories tools to the hand gun proceed as follows (Fig. Move the connector button (8) on the accessory to the "open" position. Attach the required tool to the hand gun. CORRECT USE OF THE PRODUCT This appliance is intended for use as a steam generator as described and in accordance with the instructions provided in this manual. Please read these instructions carefully and keep them, as you may find them useful in future. 3b. Move the connector button (8) back to the position `closed' 4b. Check that the connector button has engaged and the accessory is fully connected. PAT E N T E D S A F E T Y C A P / ' WAT E R O U T ' All POLTI machines are equipped with the unique Polti patented safety cap, which prevents opening of the generator tank as long as there is any pressure remaining inside the tank. This is an important and indispensable safety device, and it is necessary to follow certain procedures when re-filling the tank. According to model, `water out' is indicated by a warning light (J), or by an audible alarm signal from the machine, or on more basic models by the exhaustion of the steam output. When you have used up all the water in the tank, follow the following procedures: 1c. Switch off the machine at the generator on/off switch (B) 2c. Press the steam request lever (3) on the hand gun (2) so as to fully exhaust the steam supply from the tank. Disconnect the power supply cable (F) from the mains. Unscrew anti-clockwise the patented safety cap (A). Wait for a few minutes to allow the generator tank to cool down. When cool proceed to carefully refill the tank as described in I M P O R TA N T Before leaving our factory all our products are rigorously tested. However, your VAPORETTO may contain some residual water in the boiler. SET UP Before using VAPORETTO for the first time assemble the pivoting wheels as indicated in the diagram. P R E PA R AT I O N F O R U S E 1. Unscrew the patented safety cap (A) and fill the generator with 1. 3 litres of water, using the filler funnel (11) (Fig. [. . . ] Your glass wilI remain cleaner longer thanks to the absence of layers of film normally left behind by chemical cleaning products on which new dust and grease can attach itself. Cleaning glass is done in two stages: - Spraying the steam onto the surface to be cleaned to loosen the dirt (not touching with blade). - Pulling the blade straight down the window surface from top to bottom without applying the steam, to take away the dirt. - To clean especially large glass surfaces, attach the Window Squeegee Tool to the extension tubes. [. . . ]