User manual POLYCOM KIRK WIRELESS SERVER 600V3 INSTALLATION AND CONFIGURATION GUIDE V3

[. . . ] 14117800, Ed. 3. 0 September 28, 2010 Polycom KIRK Wireless Server 600v3 Installation and Configuration Guide ® ® 2 Copyright © Polycom, Inc. 14117800 Version 3. 0 Proprietary and Confidential The information contained herein is the sole intellectual property of Polycom, Inc. No distribution, reproduction or unauthorized use of these materials is permitted without the expressed written consent of Polycom, Inc. Information contained herein is subject to change without notice and does not represent commitment of any type on the part of Polycom, Inc. [. . . ] Page: Enter Network Password dialog box 1 2 3 In the User Name field, type the user name. In the Password field, type the password. Click OK. 14117800, Ed. 3. 0 Configuring KIRK Wireless Server 600v3 111 7. 6. 4. 2 Assigning a Specific IP Address (Secondary) To assign a specific IP address to the KWS600v3, it is necessary to disable the DCHP mode and then assign a specific IP address to the KWS600v3. The new IP address and network address will be provided by the system administrator. Note: It is advisable that the IP addresses for KWS600v3 secondaries are numbered in succession; eg. 192. 168. 1. 3, 192. 168. 1. 4, 192. 168. 1. 5 etc. This makes it easier to detect a specific Secondary KWS600v3. 1 Under the Configuration menu, click ETH0, and then click DHCP. Figure 51 Adm. Page: Configuration/ETH0/DHCP page 2 3 4 From the Mode list, select Disabled, and then click OK. Click Reset (under Administration menu) to save your configuration. Under the Configuration menu, click ETH0, and then click IP. Note: It is necessary to use the ETH0 port when integrating the KWS600v3 on the local network. Figure 52 Adm. Page: Configuration/ETH0/IP page KIRK Wireless Server 600v3 Installation and Configuration Guide 112 Configuring KIRK Wireless Server 600v3 5 In the IP address field, type the new IP address. The new IP address is now the default address when accessing the KWS600v3. In the Network mask field, type a new network mask. In the Default gateway field, type the IP address of the default gateway. Contact your system administrator for more information. Click Reset (under Administration menu) to save your configuration. 6 7 8 9 7. 6. 4. 3 Configuring Ethernet Link (Secondary) 1 Under the Configuration menu, click ETH0, and then click Link. Figure 53 Adm. Page: Configuration/ETH0/Link page 2 From the Link list, select auto, and then click OK. When selecting auto, the link speed will be determined by the network switch. Click Reset (under Administration menu) to save your configuration. 3 14117800, Ed. 3. 0 Configuring KIRK Wireless Server 600v3 113 7. 6. 4. 4 Setting LDAP Replicators (Secondary) In a KWS600v3 Multi-cell solution the Secondary KWS600v3 needs access to the information (such as system ARI code and user data) that is stored on the Master KWS600v3/LDAP Server. Therefore, it is necessary to activate the LDAP replicator services for the Secondary KWS600v3. [. . . ] You should have a telephone which does not require electricity available for use during power outages. Information to user: The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. LIMITED WARRANTY This limited, non-transferable warranty is provided to the original purchaser. The product is warranted to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the date of purchase as shown on the purchaser's receipt. [. . . ]