User manual PORT DESIGNS LUGANO COLORS 15.4 PRODUCT SHEET

[. . . ] • Never leave the packing components (plastic bags , polystyrene foam , nails , etc. ) within the reach of children since these are a source of potential danger. € The appliance must be installed by a qualified technician in compliance with the instructions provided by the manufacturer. € The latter denies all responsibility for improper installation which may harm persons and animals and damage property. [. . . ] Collegamenti elettrici Tensione Frequenza Fusibili Sezioni To install the cable, proceed as follows: • unscrew the wire clamp screw and the contact screws. € to make the desired electrical connection (see table), use the jumpers housed inside the box. Position the power supply cable wires according to the indications in the table. € once the connections have been made, tighten all the terminal screws fully. € Fasten the supply cable in place with the clamp and close the cover of the terminal board. N L FR-BE-AT-DE-GR-ES-ILIT-NZ-PT-GP-CH-MA-LUIE-FI-SE-IS-GB-NL-DK 230V - 1+N~ 50Hz CY-MT-AU-NZ-KW 240V - 1+N~ 50Hz 25A * 2, 5 mm² BL BR This appliance conforms with the following European Community Directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent amendments; - 89/336/EEC of 03/05/89 (Electromagnetic compatibility) and subsequent amendments; - 93/68/EEC of 22/07/93 and subsequent amendments; - 2002/96/EC The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. Warning: If the hob is fitted above a built-in oven, the hob and the oven must be connected to the mains separately for safety reasons and to simplify operations when it is necessary to pull the oven out for some reason. Electrical connections Voltage, Frequency FR-AT-BE-DE-GP-ES-IE-IL-IS-IT-LURE-FI-GB-GR-PT-SE-MA-NZ 230V-1+N~50 Hz FR-BE-NO 230V-2~50/60 Hz FR-BE-CH-DE-AT-ES-IL-IT-NZ-PTMA- LU-SE-IS-NL 400V2-N~50 Hz FR-BE-NO 230V3~50 Hz NL 230V2+2-N~50 Hz CY-AU-NZ-KW-MT 240V-1+N~50 Hz Fuses, Sections N L FR-BE-NO 230V - 2 ~ 50Hz BL BR BR=BRUN, BL=BLEU BR=BRUIN, BL=BLAUW BR=BRAUN, BL=BLAU BR=BROWN, BL=BLUE 1 2 L 3 4 5 N * Applicazione del fattore di simultaneità in conformità alla norma CEI 60335-2-6 25 A* 2, 5 mm² Valid only for models without a power supply cable Some models are not fitted with a power supply cable, as the cable should be sized according to the type of electrical connection in use (see connection table below). To speed up the rise in temperature of the cooking zones (see cooking zone table on the previous page), press the key. the power display will indicate “P”. The booster function comes to an automatic stop after 4 minutes. When the booster function is on, certain cooking zones (see the cooking zone table on the previous page) are limited to a maximum power of 600W. the power display will indicate “P”. KBT8424 IDO 400 - KBT8424 IDO - KOT7424 IO KBT6323 IO: you may programme all the cooking zones simultaneously for a maximum cooking time of 99 minutes. Proceed as follows: • select the cooking zone by pressing the corresponding control key, • set the desired heating power using the “+” and “-” keys, • press the programming key , • set the desired cooking time using the “+” and “-” keys, • confirm your programming by pressing the programming key again. The end of programmed cooking is signalled by a beep (one minute long) and the cooking zone concerned is turned off. The safety devices Pan recognition Each induction cooking zone is fitted with a pan recognition device. The cooking zone only provides heat in the presence of a pan which is suitable for the cooking zone. A blinking pan recognition indicator could signal: • that the pan is made of unsuitable material, which is not ferromagnetic, • that the diameter of the pan is too small, • that the pan has been removed. [. . . ] Avoid using pans used normally on gas burners. The concentration of heat on gas burners can warp the bottom of the pan, consequently you would never obtain the desired result when using the pan on the glass ceramic hob. Never leave a cooking zone on without a pan on it as the maximum heat level would be reached very quickly, which could damage the heating elements. the glass ceramic hob is resistant to thermal and mechanical shocks. [. . . ]