User manual POULAN PRO 961980019

[. . . ] IMPORTANT MANUAL Do Not Throw Away OWNER'S MANUAL MODEL NUMBER: 961980019 SNOW THROWER Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. WARNING: Always Wear Eye Protection During Operation 415326 10. 03. 07 TH Printed in the U. S. A. Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. Look for this symbol to point out important safety precautions. [. . . ] Engine will not develop full power until it has reached normal operat11 ing temperature. FIG. 22 OPERATION WARM START - ELECTRIC STARTER Follow the steps above, keeping the choke control in the "OFF" position. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. Keep the extra safety ignition key in a safe place. Place ON / OFF switch in "ON" position. Rotate choke control to "FULL position. Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the "OFF" position. Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the "OFF" position. BEFORE STOPPING Run the engine for a few minutes to help dry off any moisture on the engine. IF RECOIL STARTER HAS FROZEN If the recoil starter has frozen and will not turn the engine, proceed as follows: 1. Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible. Release the recoil starter handle and let it snap back against the starter. If the engine still fails to start, repeat the above steps or use the electric starter. · · · · · Adjust the skid plates to proper height for current snow conditions. See "TO ADJUST SKID PLATES" in this section of this manual. For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly. [. . . ] Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29 REPAIR PARTS WHEELS / DECALS SNOW THROWER - MODEL 961980019 (96198001901) 1 2 5 4 6 7 5 7 3 6 2 7 30 REPAIR PARTS WHEELS / DECALS SNOW THROWER - MODEL 961980019 (96198001901) KEY PART NO. NO. DESCRIPTION 1 2 3 4 5 6 7 187833X421 155443 187865X421 146315 179830 174697 17490508 Wheel Assembly, 16", LH Pin, Klik 1/4 Wheel Assembly, 16", RH Screw, Hex Head, Tapping 5/16-18 x 5/8 Bearing, Axle Washer, Thrust (1") Screw, Hex Head 5/16-18 x 1/2 KEY PART NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 --- 181037 199436 181035 181042 199437 181033 415391 415390 415475 183730 415326 415327 Decal, Danger Decal, Aug Poul Pro Decal, Danger, Deflector Decal, Danger Decal Decal, Instruction Decal, Traction Lever Decal, Auger Lever Decal, Speed Control Decal, Remote Deflector Owner's Manual, English Owner's Manual, French NOTE: All component dimensions given in U. S. [. . . ]