User manual POULAN HD145H42H

[. . . ] WARNING: Always Remove safety ignition key and disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping surfaces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings. WARNING: Snow throwers have exposed rotating parts, which can cause severe injury from contact, or from material thrown from the discharge chute. [. . . ] Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. Keep the extra safety ignition key in a safe place. Place throttle control in FAST position. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. Push starter button until engine starts. IMPORTANT: Do not crank engine more than five continuous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt. When the engine starts, release the starter button and slowly move the choke control to the "OFF" position. Disconnect the power cord from the receptacle first, then from the engine. Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. At this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures. Slightly overlap each successive path to ensure all snow will be removed. Adjust the skid plates to proper height for current snow conditions. See "TO ADJUST SKID PLATES" in this section of this manual. For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly. Keep engine clean and clear of snow during use. This will help air flow and extend engine life. After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine. Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use. WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower. 12 MAINTENANCE GENERAL RECOMMENDATIONS The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. [. . . ] 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 49 50 51 52 53 57 58 851084 155452 192213 178830 17490408 402881 403096X004 198580 405485 191730 402856X004 187101 402857X004 413429 700279 73930500 403097X004 17000616 175324X479 410877 184471 409345X428 402685X428 406109 57079 35062 11050500 198563 DESCRIPTION Screw, Hex Head 3/8-24 x 1-3/8 Guide, Belt Belt Cover Assembly (Includes Toolbox Cover) Cover, Toolbox Screw, Hex Head 1/4-20 x 1/2 Bolt, Shoulder 5/16-18 Bellcrank Shifter Clevis Pin Arm, Auger Control Locknut, Hex Plate, Clutch Link, Speed Control Bracket, Clutch Bracket, Traction Hairpin, Cotter 3/32 x 1/2 Locknut, Hex Plate, Shifter Screw, Hex Head Pivot Bracket, Impeller Idler Arm Pan, Frame Bottom Screw Frame Assembly Plate, Frame End Shaft, Auger Control Washer, Hardened Key, Safety Washer, Lock, External Tooth Power Cord 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 74780520 150078 59289 166785 175330 179092 10040500 17490508 410420 85179 178828 408010 150406 187786X008 74780524 175331 180523 74610516 409475 180478 179157 400026 850263 NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29 REPAIR PARTS SNOW THROWER - - MODEL NO. [. . . ]