User manual POULAN 3400

[. . . ] WARNING: Always remove safety ignition key and disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping surfaces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings. [. . . ] The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A. C. · Be sure your house is a 120 Volt A. C. If you are uncertain, consult a licensed electrician. WARNING: Do not use the electric starter if your house is not a 120 Volt A. C. Serious personal injury or damage to your snow thrower could result. OPERATION COLD START - ELECTRIC STARTER 1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. Keep the extra safety ignition key in a safe place. Place throttle control in FAST position. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. Push starter button until engine starts. IMPORTANT: Do not crank engine more than five continuous seconds between each time you try to start. Full throttle offers the best performance. Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the throttle, to adjust speed. It is easier and more efficient to remove snow immediately after it falls. The best time to remove snow is the early morning. At this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures. Slightly overlap each successive path to ensure all snow will be removed. Adjust the skid plates to proper height for current snow conditions. See "TO ADJUST SKID PLATES" in this section of this manual. For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly. Keep engine clean and clear of snow during use. [. . . ] 27 REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001801) CHASSIS / ENGINE / PULLEYS 30 3 53 58 19 17 57 6 22 23 28 6 10 21 5 31 29 56 4 10 21 24 25 18 20 26 27 31 32 36 32 37 11 36 44 43 33 34 35 11 45 41 39 50 11 8 38 5 16 1 5 26 42 9 12 7 13 14 15 44 52 49 47 5 51 40 46 28 REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001801) CHASSIS / ENGINE / PULLEYS KEY PART NO. 1 2 3 414557 180522 --- DESCRIPTION Spring, Traction Idler Pulley, Idler (2-1/4) Engine, Tecumseh, Model Number LH358SA (For engine service and replacement parts, call Tecumseh Products at 1-800-558-5402) Screw, Hex Head 5/16-18 x 1-1/4 Screw Washer, Flat Nut, Jam, Lock 5/16-18 Pin, Idler Pivot V-Belt, Traction Drive Washer, Lock 5/16 Screw, Hex Washer Head 5/16-18 x 1/2 Impeller Arm Assembly Retainer, Hairpin Spring, Brake V-Belt, Impeller Drive Screw, Hex Head 3/8-16 x 1-1/4 Arm, Idler Screw, Hex Head 5/16-18 x 1-1/2 Bushing, Idler Pivot Pulley, Idler (2-3/4) Screw, Hex Head 5/16-24 x 1 Spacer, Engine Pulley Pulley, Engine, Traction Drive Pulley, Engine, Impeller Drive Washer, Flat 3/8 Washer, Lock 3/8 KEY PART NO. 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 49 50 51 52 53 56 57 58 851084 155452 192213 178830 17490408 402881 403096X004 198580 405485 191730 402856X004 187101 402857X004 413429 700279 73930500 403097X004 17000616 175324X479 410877 184471 409346X428 402685X428 406109 57079 35062 417014X428 11050500 198563 DESCRIPTION Screw, Hex Head 3/8-24 x 1-3/8 Guide, Belt Belt Cover Assembly (Includes Toolbox Cover) Cover, Toolbox Screw, Hex Head 1/4-20 x 1/2 Bolt, Shoulder 5/16-18 Bellcrank Shifter Clevis Pin Arm, Auger Control Locknut, Hex Plate, Clutch Link, Speed Control Bracket, Clutch Bracket, Traction Hairpin, Cotter 3/32 x 1/2 Locknut, Hex Plate, Shifter Screw, Hex Head Pivot Bracket, Impeller Idler Arm Pan, Frame Bottom Screw Frame Assembly Plate, Frame End Shaft, Auger Control Washer, Hardened Key, Safety Plate, Engine Washer, Lock, External Tooth Power Cord 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 74780520 150078 59289 166785 175330 416954 10040500 17490508 410420 85179 178828 408007 150406 187786 74780524 175331 180523 74610516 409475 180478 179157 400026 850263 NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. [. . . ]