User manual POULAN P8527ESA

[. . . ] IMPORTANT MANUAL Do Not Throw Away OWNER'S MANUAL MODEL NUMBER: WARNING: Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. P8527ESA SNOW THROWER Always Wear Eye Protection During Operation 185143 10. 24. 02 BY Printed in U. S. A. SAFETY RULES Safe Operation Practices for Snow Throwers IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. · Do not operate the equipment without wearing adeLook for this symbol to point out imquate winter outer garments. [. . . ] Insert safety ignition key into the ignition slot until it clicks. Keep the extra safety ignition key in a safe place. Place throttle control in FAST position. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. NOTE: Do not use primer when starting engine with the electric starter. Push starter button until engine starts. IMPORTANT: Do not crank engine more than five continuous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt. When the engine starts, release the starter button and slowly move the choke control to the OFF position. Disconnect the power cord from the receptacle first, then from the engine. Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. WARM START - ELECTRIC STARTER Follow the steps above, keeping the choke control in the OFF position. Insert safety ignition key into the ignition slot until it clicks. Keep the extra safety ignition key in a safe place. Place throttle control in FAST position. Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position. Allow the engine to warm up for a few minutes. [. . . ] DESCRIPTION 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 46 47 48 49 50 51 52 53 54 55 181044 180522 --74780520 59289 73930500 175330 179092 850263 150078 184789 85179 178828 183533 150406 179354X008 74780524 175331 180523 74610516 179371 180478 179157 62735 851084 155452 180465 178830 17490408 179256 179250 180401 179240 73800500 178833X479 179251 179064 178890 76020208 179065 179063X479 74780624 178624X479 71020512 181156 183852X428 178693X428 179068X008 57079 179062 12000010 700279 Spring, Traction Idler Pulley, Idler (2-1/4) Engine, Tecumseh, Model Number HMSK85 (Order parts from Engine manufacturer) Screw, Hex Head 5/16-18 x 1-1/4 Washer, Flat Nut, Jam, Lock 5/16-18 Pin, Idler Pivot V-Belt, Traction Drive Washer, Lock 5/16 Screw, Hex Head 5/16-18 x 3/4 Impeller Idler Arm & Bracket Assembly (Includes Key numbers 8 and 13) Retainer, Hairpin Spring, Brake V-Belt, Impeller Drive Screw, Hex Head 3/8-16 x 1-1/4 Arm, Idler Screw, Hex Head 5/16-18 x 1-1/2 Bushing, Idler Pivot Pulley, Idler (2-3/4) Screw, Hex Head 5/16-18 x 1 Spacer, Engine Pulley Pulley, Engine, Traction Drive Pulley, Engine, Impeller Drive Washer, Flat 3/8 Screw, Hex Head 3/8-24 x 1-3/8 Guide, Belt Cover, Belt Cover, Toolbox Screw, Hex Head 1/4-20 x 1/2 Bolt, Shoulder 5/16-18 Bellcrank Shifter Screw, Hex Head 1/4-28 x 3/4 Arm, Auger Control Nut, Lock 5/16-18 Bellcrank Assembly Link, Speed Control Trunnion, Pivot Bracket Nut, Cage 3/8-16 Pin, Cotter 1/16 x 1/2 Pin, Pivot Bracket Bracket, Bellcrank Screw, Hex Head 3/8-16 x 1-1/2 Pan, Frame Bottom Screw, Hex Head 5/16-18 x 3/4 Nut, Speed 5/16-18 Frame Assembly Plate, Frame End Shaft, Auger Control Washer, Hardened Roller Ring, Retaining Clip, Retainer NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm 29 REPAIR PARTS WHEELS / DECALS 10 18 15 19 31 4 17 12 10 SNOW THROWER - MODEL NUMBER P8527ESA 10 24 14 22 23 21 20 25 33 13 11 26 10 29 27 32 30 8 1 7 28 2 1 3 4 2 9 10 18 32 30 16 11 29 27 28 28 11 23 33 25 24 26 22 19 15 12 7 4 5 6 14 13 11 4 10 3 21 20 1 2 4 12 9 8 6 5 1 3 30 11 10 7 REPAIR PARTS WHEELS / DECALS KEY PART NO. NO. SNOW THROWER - MODEL NUMBER P8527ESA DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 178834 155443 181843 17541008 73800500 155415 71210616 182064X479 182044X479 150078 17490508 184393 184288X479 182015 184361 181982 182063 181847 85179 179148X479 179141 182466 179136 179138 179139 179137 178879 174697 179830 182226 4802 700279 12000045 Wheel Assembly (16" Power Steer) Pin, Klik 1/4 Cover, Power Steering Screw, Hex Head #10-24 x 1/2 Nut, Lock 5/16-18 Washer, Flat 5/16 Screw, Hex Head 3/8-16 x 1 Bracket, Steer Cable RH Bracket, Steer Cable LH Screw, Hex Head 5/16-18 x 3/4 Screw, Hex Head 5/16-18 x 1/2 Link, Steering Lever Lever Assembly, Steering Pin, Steering Lever Bellcrank Assembly Bracket Assembly, LH Steering Bracket Assembly, RH Steering Pin, Steering Bellcrank Retainer, Hairpin Bracket, Lever Assembly Driver, Wheel Ring, Wire Retainer Lobe, Wheel Slide, Clutch Spring, Clutch Slide Lobe, Axle Key, Square 1/4 Washer, Thrust (1") Bearing, Axle Spring, Return Washer, Flat Clip, Retainer Ring, Retaining KEY PART NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 --- 181037 183881 181035 181042 183879 181033 155798 155800 181039 183730 183907 183905 185143 185148 Decal, Danger Decal, Poulan, 8. 5 HP/27" Decal, Danger, Deflector Decal, Danger Decal, Poulan Decal, Instruction Decal, Traction Lever Decal, Auger Lever Decal, Speed Control Decal, Remote Deflector Decal, LH Trigger Decal, RH Trigger Owner's Manual (English) Owner's Manual (French) NOTE: All component dimensions given in U. S. [. . . ]