User manual POULAN PO17542STB

[. . . ] PO17542STB 17. 5 HP 42 Inch Lawn Tractor For Parts and Service, contact our authorized distributor: call 1-800-849-1297 For Technical Assistance: call 1-800-829-5886 190781 Rev. 1 03. 01. 04 RD/TR PRINTED IN U. S. A. SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION · · · · · · · · · · · · · · · · Read, understand, and follow all instructions in the manual and on the machine before starting. [. . . ] Check operator presence and interlock systems for proper operation. Check for loose fasteners. SAE 30 OR 10W30 MOTOR OIL GENERAL PURPOSE GREASE REFER TO MAINTENANCE "ENGINE" SECTION GEARSHIFT PIVOTS 14 IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY. MAINTENANCE TRACTOR Always observe safety rules when performing any maintenance. TRAILING EDGE UP BLADE CENTER HOLE FLAT WASHER LOCK WASHER STAR MANDREL ASSEMBLY BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual). TIRES · Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual). · Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. · Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. BLADE BOLT FIG. 9) NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine. · The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower. · To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer. ) NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not. · Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced. CENTER HOLE OPERATOR PRESENCE SYSTEM Be sure operator presence and interlock systems are working properly. If your tractor does not function as described, repair the problem immediately. · The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position. [. . . ] Please refer to the applicable manufacturer's warranty on these items. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser unless such return is requested by Electrolux Home Products. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find to be defective in manufacture, during the first ninety (90) days of ownership. [. . . ]