User manual POULAN PRO PP1130ESA

[. . . ] IMPORTANT MANUAL Do Not Throw Away OWNER'S MANUAL MODEL NUMBER: WARNING: Read the Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. PP1130ESA SNOW THROWER Always Wear Eye Protection During Operation 183615 Rev. 6 09. 30. 02 BY Printed in U. S. A. SAFETY RULES Safe Operation Practices for Snow Throwers IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. [. . . ] Serious personal injury or damage to your snow thrower could result. OPERATION COLD START - ELECTRIC STARTER 1. Insert safety ignition key into the ignition slot until it clicks. Keep the extra safety ignition key in a safe place. Place throttle control in FAST position. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. NOTE: Do not use primer when starting engine with the electric starter. Push starter button until engine starts. IMPORTANT: Do not crank engine more than five continuous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt. When the engine starts, release the starter button and slowly move the choke control to the OFF position. Disconnect the power cord from the receptacle first, then from the engine. Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. WARM START - ELECTRIC STARTER Follow the steps above, keeping the choke control in the OFF position. Insert safety ignition key into the ignition slot until it clicks. Keep the extra safety ignition key in a safe place. Place throttle control in FAST position. Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position. [. . . ] DESCRIPTION Spring, Traction Idler Pulley, Idler (2-1/4) Engine, Tecumseh, Model Number OHSK110 (Order parts from Engine manufacturer) 4 74780520 Screw, Hex Head 5/16-18 x 1-1/4 6 59289 Washer, Flat 7 73930500 Nut, Jam, Lock 5/16-18 8 175330 Pin, Idler Pivot 9 179092 V-Belt, Traction Drive 10 10040500 Washer, Lock 5/16 11 150078 Screw, Hex Head 5/16-18 x 3/4 12 184789 Impeller Idler Arm & Bracket Assembly (Includes Key numbers 8 and 13) 13 85179 Retainer, Hairpin 14 178828 Spring, Brake 15 183533 V-Belt, Impeller Drive 16 150406 Screw, Hex Head 3/8-16 x 1-1/4 17 179354X008 Arm, Idler 18 74780524 Screw, Hex Head 5/16-18 x 1-1/2 19 175331 Bushing, Idler Pivot 20 180523 Pulley, Idler (2-3/4) 21 74610516 Screw, Hex Head 5/16-18 x 1 22 179371 Spacer, Engine Pulley 23 180478 Pulley, Engine, Traction Drive 24 179157 Pulley, Engine, Impeller Drive 25 62735 Washer, Flat 3/8 26 10040600 Washer, Lock 3/8 27 851084 Screw, Hex Head 3/8-24 x 1-3/8 28 155452 Guide, Belt 29 180465 Cover, Belt 30 178830 Cover, Toolbox 31 17490408 Screw, Hex Head 1/4-20 x 1/2 32 179256 Bolt, Shoulder 5/16-18 33 179250 Bellcrank Shifter 34 180401 Screw, Hex Head 1/4-28 x 3/4 35 179240 Arm, Auger Control 36 73800500 Nut, Lock 5/16-18 37 178833X479 Bellcrank Assembly 38 179251 Link, Speed Control 39 179064 Trunnion, Pivot Bracket 40 178890 Nut, Cage 3/8-16 41 76020208 Pin, Cotter 1/16 x 1/2 42 179065 Pin, Pivot Bracket 43 179063X479 Bracket, Bellcrank 44 74780624 Screw, Hex Head 3/8-16 x 1-1/2 46 178624X479 Pan, Frame Bottom 47 71020512 Screw, Hex Head 5/16-18 x 3/4 48 181156 Nut, Speed 5/16-18 49 183852X428 Frame Assembly 50 178693X428 Plate, Frame End 51 179068X008 Shaft, Auger Control 52 57079 Washer, Hardened 53 179062 Roller 54 12000010 Ring, Retaining 55 700279 Clip, Retainer NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm 29 1 2 3 181044 180522 --- REPAIR PARTS WHEELS / DECALS 10 18 15 19 31 4 17 12 10 SNOW THROWER - MODEL NUMBER PP1130ESA 10 24 14 22 23 21 20 25 33 13 11 26 10 29 27 32 30 8 1 7 28 2 1 3 4 2 9 10 18 32 30 16 11 29 27 28 28 11 23 33 25 24 26 22 19 15 12 7 4 5 6 14 13 11 4 10 3 21 20 1 2 4 12 9 8 6 5 1 3 30 11 10 7 REPAIR PARTS WHEELS / DECALS KEY PART NO. NO. SNOW THROWER - MODEL NUMBER PP1130ESA DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 178834 155443 181843 17541008 73800500 155415 71210616 182064X479 182044X479 150078 17490508 184393 184288X479 182015 184361 181982 182063 181847 85179 179148X479 179141 182466 179136 179138 179139 179137 178879 174697 179830 182226 4802 700279 12000045 Wheel Assembly (16" Power Steer) Pin, Klik 1/4 Cover, Power Steering Screw, Hex Head #10-24 x 1/2 Nut, Lock 5/16-18 Washer, Flat 5/16 Screw, Hex Head 3/8-16 x 1 Bracket, Steer Cable RH Bracket, Steer Cable LH Screw, Hex Head 5/16-18 x 3/4 Screw, Hex Head 5/16-18 x 1/2 Link, Steering Lever Lever Assembly, Steering Pin, Steering Lever Bellcrank Assembly Bracket Assembly, LH Steering Bracket Assembly, RH Steering Pin, Steering Bellcrank Retainer, Hairpin Bracket, Lever Assembly Driver, Wheel Ring, Wire Retainer Lobe, Wheel Slide, Clutch Spring, Clutch Slide Lobe, Axle Key, Square 1/4 Washer, Thrust (1") Bearing, Axle Spring, Return Washer, Flat Clip, Retainer Ring, Retaining KEY PART NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 --- 181037 183888 181035 181042 183876 181033 155798 155800 181039 183730 183907 183905 183615 184744 Decal, Danger Decal, Poulan Pro, 11HP/30" Decal, Danger, Deflector Decal, Danger Decal, Poulan Pro Decal, Instruction Decal, Traction Lever Decal, Auger Lever Decal, Speed Control Decal, Remote Deflector Decal, LH Trigger Decal, RH Trigger Owner's Manual (English) Owner's Manual (French) NOTE: All component dimensions given in U. S. [. . . ]