User manual POULAN PRO PP15H42KA

[. . . ] WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping surfaces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings. [. . . ] · When not using drift cutters, loosen adjustment nut, lower to storage position and tighten nut securely. AUGER HOUSING STORAGE POSITION DRIFT CUTTER SAFETY IGNITION KEY GASOLINE FILLER CAP FUEL SHUTOFF VALVE RECOIL STARTER HANDLE STARTER BUTTON POWER CORD PLUG ADJUSTMENT NUT FIG. 20 NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT. 21 12 OPERATION TO START ENGINE · Be sure fuel shut-off valve is in the "OPEN" position. Your snow thrower engine is equipped with both a 120 Volt A. C. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A. C. · Be sure your house is a 120 Volt A. C. If you are uncertain, consult a licensed electrician. WARNING: Do not use the electric starter if your house is not a 120 Volt A. C. Serious personal injury or damage to your snow thrower could result. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the "OFF" position. BEFORE STOPPING Run the engine for a few minutes to help dry off any moisture on the engine. IF RECOIL STARTER HAS FROZEN If the recoil starter has frozen and will not turn the engine, proceed as follows: 1. Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible. Release the recoil starter handle and let it snap back against the starter. If the engine still fails to start, repeat the above steps or use the electric starter. SNOW THROWING TIPS · · · · · · · · · · · Always operate the snow thrower with the engine at full throttle. Full throttle offers the best performance. Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the throttle, to adjust speed. It is easier and more efficient to remove snow immediately after it falls. [. . . ] 27 REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902) CHASSIS / ENGINE / PULLEYS 30 3 53 58 19 17 57 6 22 23 28 6 10 21 5 31 29 56 4 10 21 24 25 18 20 26 27 31 32 36 32 37 11 36 44 43 33 34 35 11 45 41 39 50 11 8 38 5 16 1 5 26 42 9 12 7 13 14 15 44 52 49 47 5 51 40 46 28 REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902) CHASSIS / ENGINE / PULLEYS KEY PART NO. 1 2 3 414557 180522 --- DESCRIPTION Spring, Traction Idler Pulley, Idler (2-1/4) Engine, Tecumseh, Model Number LH358SA (For engine service and replacement parts, call Tecumseh Products at 1-800-558-5402) Screw, Hex Head 5/16-18 x 1-1/4 Screw Washer, Flat Nut, Jam, Lock 5/16-18 Pin, Idler Pivot V-Belt, Traction Drive Washer, Lock 5/16 Screw, Hex Washer Head 5/16-18 x 1/2 Impeller Arm Assembly Retainer, Hairpin Spring, Brake V-Belt, Impeller Drive Screw, Hex Head 3/8-16 x 1-1/4 Arm, Idler Screw, Hex Head 5/16-18 x 1-1/2 Bushing, Idler Pivot Pulley, Idler (2-3/4) Screw, Hex Head 5/16-24 x 1 Spacer, Engine Pulley Pulley, Engine, Traction Drive Pulley, Engine, Impeller Drive Washer, Flat 3/8 Washer, Lock 3/8 KEY PART NO. 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 49 50 51 52 53 56 57 58 851084 155452 192213 178830 17490408 402881 403096X004 198580 405485 191730 402856X004 187101 416717X004 413429X479 700279 73930500 403097X004 17000616 175324X479 410877 184471 409346X428 402685X428 406109 57079 35062 417014X428 11050500 198563 DESCRIPTION Screw, Hex Head 3/8-24 x 1-3/8 Guide, Belt Belt Cover Assembly (Includes Toolbox Cover) Cover, Toolbox Screw, Hex Head 1/4-20 x 1/2 Bolt, Shoulder 5/16-18 Bellcrank Shifter Clevis Pin Arm, Auger Control Locknut, Hex Plate, Clutch Link, Speed Control Bracket, Clutch Bracket, Traction Hairpin, Cotter 3/32 x 1/2 Locknut, Hex Plate, Shifter Screw, Hex Head Pivot Bracket, Impeller Idler Arm Pan, Frame Bottom Screw Frame Assembly Plate, Frame End Shaft, Auger Control Washer, Hardened Key, Safety Mounting Plate, Engine Washer, Lock, External Tooth Power Cord 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 74780520 150078 59289 166785 175330 407908 10040500 17490508 410420 85179 178828 408007 150406 187786 74780524 175331 180523 74610516 409475 180478 179157 400026 850263 NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. [. . . ]