User manual POULAN XC1182B

[. . . ] ADVERTENCIA: Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves. AVERTISSEMENT: Lire le manuel d'instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. Tout défaut de le faire pourrait entraîner des blessures graves. Poulan PRO 7349 Statesville Road Charlotte, NC 28269 Poulan PRO 850 Matheson Blvd. [. . . ] Pivot shield until bolt passes through hole in bracket. Bracket Shield Slot 4. Reinstall wing nut and tighten securely. Upper Shaft Locking/ Release Attachment Button WingNut WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before operating the unit. All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual. Using the wrong hole could lead to serious injury or damage to the unit. 9 ADJUSTING THE HANDLE WARNING: When adjusting the handle, be sure it remains above the safety label and below the mark or arrow on the shaft. 1. Rotate the handle on the shaft to an upright position; retighten wing nut. OPERATION KNOW YOUR UNIT READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Assist handle Coupler ON/STOP switch Trimmer head Shaft Shield Throttle lock-out Choke lever Muffler Line limiter blade Throttle trigger Primer bulb Starter handle ON/STOP SWITCH The ON/STOP switch is used to stop engine. To stop the engine, move the switch to the STOP position. CHOKE PRIMER BULB The PRIMER BULB removes air from the carburetor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate the primer bulb by pressing it and allowing it to return to its original form. The CHOKE helps to supply fuel to the engine to aid in cold starting. Activate the choke by moving the choke lever to the FULL CHOKE position. Move choke lever to HALF CHOKE position . Pull starter rope sharply until engine starts, but no more than 10 pulls. Allow the engine to run for 30- seconds. -45 NOTE: If the engine doesn't start after 10 pulls (at the HALF CHOKE position ), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 10 pulls. If the engine still doesn't start, it is probably flooded. Once the engine starts and has ran for 10-15 seconds at the HALF CHOKE position , move the choke lever to the RUN position . Allow the unit to run for 30 seconds before releasing the throttle trigger. NOTE: If engine dies with the choke lever in the RUN position , move the choke lever to the HALF CHOKE and pull the rope until enposition gine runs, but no more than 6 pulls. Starting position If your engine still does not start after following these instructions, please call 1- 800- 554- 6723. prevent unintentional use of the throttle trigger. [. . . ] Where a warrantable condition exists, Poulan PRO will repair your small off-road engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor. MANUFACTURER'S WARRANTY COVERAGE: If any emissions related part on your engine (as listed under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or replaced by Poulan PRO. OWNER'S WARRANTY RESPONSIBILITIES: As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your instruction manual. [. . . ]