User manual PRO-JECT 2 XPERIENCE COMFORT

[. . . ] Remove the transport lock (18) from the tonearm. Store it together with the two red motor transport screws (1) in the original packaging so they are available for any future transportation. Mains power connection The turntable is supplied with a power supply suitable for your country's mains supply. Check the label before connecting to ensure compliance with the mains rating in your house. Connect the low voltage plug from the power supply to the socket (13) on the rear of the record player before connecting the power supply to the mains. Switching on and off Pressing the power switch (20) alternately starts or stops the motor. Cartridge downforce adjustment Counterweigts supplied: 2 Xperience with Sumiko Blue Point No. [. . . ] Avoid getting sweat or grease on the belt as these will deteriorate the performance and reduce the belt's lifespan. Use absorbent kitchen paper to remove any oil or grease from the outer edge of the hub and the belt. Level the plinth using a spirit level and the adjustable feet (23). Adjusting the vertical tracking angle (vta) ** Put a record and the record weight on the platter. When the needle is lowered into the record groove and the tonearm is not resting on the lift arm, the tube of the tonearm should be parallel to the surface of the record. If it is not loosen both allen screws in the tonearm base just enough to allow vertical movement of the arm pillar without force and slide the arm up or down until it is parallel. Carefully retighten the allen screws without applying excessive force (which would deform the arm pillar) ­ finger tight is quite sufficient. 4 © Audio Trade GmbH · Pro-Ject 2 Xperience Comfort / Ort 2M Red_Sum BP2_Ort RR · Revision 1. 3. 08/1. 5. 08 Adjusting the azimuth ** The cartridge needle must be vertical in the record groove in order to trace the groove wall modulations correctly. A small screw at the bearing end of the arm allows incorrect azimuth to be Screw corrected if your needle is not mounted exactly perpendicular to the cartridge body (which is often the case). Slacken off the screw just enough to be able to revolve the arm tube without applying force. With the aid of a good magnifying glass adjust the needle until it is vertical in the groove (i. e. perpendicular to the record's surface). Ideally this should correspond to the top surface of the cartridge body being parallel to the record surface. When you are satisfied that the needle is vertical retighten the screw carefully. Under no circumstances should the arm tube be adjusted with the needle still in the record groove!Irreparable damage may be caused to the cantilever suspension!The arm must be lifted to make each adjustment and lowered afterwards to check it. Anti-skating force adjustment The anti-skating force must be adjusted according to the mass of the cartridge as follows: Downforce Groove in the stub (15) 10 - 14mN 1st from bearing rings 15 - 19mN 2nd " " " 20mN and bigger 3rd " " " Slip the loop of the anti-skating weight's thread over the third groove of the stub to set the correct anti-skating force for the factory-fitted cartridge. Feed the thread through the loop of the wire support (17). Connection to the amplifier The record player has gold plated female RCA phono sockets (14) so you can substitute the interconnect cables supplied with those of your choice for connection to the amplifier if you wish. Your dealer can advise you on alternative cables. Use the Phono input (sometimes labelled gram, disc or RIAA) on your amplifier. Make sure that the phono input offers correct matching and amplification for the type of cartridge used. Line inputs (such as CD, Tuner, Tape or Video) are not suitable. Take care to connect the left and right channels correctly. The right channel is usually marked red, the left channel black or white. [. . . ] Particular tools like the PRO-JECT alignment tool are required to accomplish this job properly. If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing help of your PRO-JECT dealer to accomplish this task for you. Whilst adjusting the cartridge alignment with an alignment protractor the drive belt must be removed and the motor must be switched on, otherwise the arm lift cannot be lowered. Technical specifications PRO-JECT 2 Xperience Comfort Electronic speed change Speed variance Wow and flutter Signal to noise Downforce range Effective tonearm length Overhang Automatic switch-off Power consumption Outboard power supply Dimensions (W x H x D) Weight 33, 33/45, 11 r. p. m. Insert the transport screws for the motor (1) and the transport lock for the tonearm (18) prior to carefully packaging the record player. Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. [. . . ]