User manual PRO-JECT 2 XPERIENCE SUPERPACK 2

[. . . ] Avoid getting sweat or grease on the belt as these will deteriorate the performance and reduce the belt's lifespan. Use absorbent kitchen paper to remove any oil or grease from the outer edge of the platter and the belt. Level the plinth using a spirit level and the adjustable feet (23). Remove the two red transport screws (1) which secure the motor (22) during transportation. [. . . ] Slacken off the screw just enough to be able to revolve the arm tube without applying force. Please note: do not remove the screw completely!With the aid of a good magnifying glass adjust the needle until it is vertical in the groove (i. e. perpendicular to the record's surface). Ideally this should correspond to the top surface of the cartridge body being parallel to the record surface. When you are satisfied that the needle is vertical retighten the screw carefully. Under no circumstances should the arm tube be adjusted with the needle still in the record groove!Irreparable damage may be caused to the cantilever suspension!The arm must be lifted to make each adjustment and lowered afterwards to check it. 4 © Audio Trade GmbH · Pro-Ject 2 Xperience SuperPack 1& 2 / Ort RR_Ort Salsa· Revision 1. 3. 08/1. 5. 08 Anti-skating force adjustment The anti-skating force must be adjusted according to the mass of the cartridge as follows: Downforce Groove in the stub (15) 10 - 14mN 1st from bearing rings 15 - 19mN 2nd " " " rd 20mN and bigger 3 " " " Hang the loop of the thread of the anti-skating weight in the groove of the anti-skating stub (15) corresponding to the downforce applied to your cartridge and feed the thread through the loop of the wire support (17). Connection to the amplifier The record player has gold plated female RCA phono sockets (14) so you can substitute the interconnect cables supplied with those of your choice for connection to the amplifier if you wish. Your dealer can advise you on alternative cables. Use the Phono input (sometimes labelled gram, disc or RIAA) on your amplifier. Make sure that the phono input offers correct matching and amplification for the type of cartridge used. Line inputs (such as CD, Tuner, Tape or Video) are not suitable. Take care to connect the left and right channels correctly. The right channel is usually marked red, the left channel black or white. Check the manual supplied with your amplifier for relevant information. An earthing wire may be connected to the screw terminal between the sockets if you encounter hum problems when using the record player. If your amplifier does not have an input suitable for phono cartridges you will require a separate phono amplifier stage for MM or MC cartridges such as the PRO-JECT PHONO BOX or the PRO-JECT TUBE BOX which is then connected between the record player and a free line level input of the amplifier. For detailed product information please refer to the Pro-Ject web site www. project-audio. com. The recommended load resistance for the Ortofon MC Rondo Red cartridge is: 10-200ohms/MC-input. The recommended load resistance for the Ortofon MC Salsa cartridge is: > 20ohms/MC-input. Connection the Speed Box, mains power connection The turntable is supplied with a power supply suitable for your country's mains supply. Check the label before connecting to ensure compliance with the mains rating in your house. [. . . ] ±0, 5 % ±0, 08 % -70dB 10-30mN 9 " (230mm) 18mm 2W 16V/500mA AC, suitable for your country's mains supply 460 x 133 x 360mm, dust cover open 460 x 390 x 460mm 7, 6kg Technical specifications PRO-JECT SPEED BOX Speed change Power output Dimensions (W x H x D) Weight without power supply 33, 33 or 45, 11 r. p. m. (power consumption 3W max. ) 80 x 20 x 85mm 300g 6 © Audio Trade GmbH · Pro-Ject 2 Xperience SuperPack 1& 2 / Ort RR_Ort Salsa· Revision 1. 3. 08/1. 5. 08 Potential incorrect use and fault conditions PRO-JECT turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common fault symptoms is included. [. . . ]