User manual PROEL FLASH12P

[. . . ] This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the enviroment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. [. . . ] Inside the amplified loudspeakers are present special safety devices such as: Fuse on rear panel. Protection against excessive power applied at each speaker. Inside the passive loudspeakers are present special safety devices such as: Protection against excessive power applied at HF-driver speaker. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Thank you for having chosen a PROEL product. FLASH is a new line of loudspeakers designed by PROEL to satisfy all of those who are looking for light, handy enclosures with an elegant look and sound quality which has been studied in every detail. Combining technology with the acquired experience in the production of speaker enclosures in synthetic material, PROEL's electro-acoustic design team mixed elements that identify Italian design around the world with stateof-the-art mechanical, acoustic and electronic solutions. The aim of this was the creation of instruments which can face any situation with the certainty of the final result. fLASH12 is a full-range , polypropylene enclosure available in both passive (FLASH12P) and active (FLASH12A) versions. One of the most interesting elements of the design is the new high frequency horn with a wide constant coverage angle, designed for extended response and low distortion levels. The transducers employed include a 1" compression driver with a titanium diaphragm and a 12" woofer with a 2" voice coil. The profile of the cabinet, which is made of sturdy light polypropylene, allows the use of this enclosure as a floor monitor, whereas four M10 suspension points are provided for installation in a variety of positions using the optional accessories available. Two convenient aluminium handles, plus a third on top of the cabinet, make for easy transportation and smooth installation. The module employed in the active version includes two amplification sections, a 50 Wrms section for the high end and a 200 Wrms, class H, section for the lows. It also features one line input, one microphone input with an independent level control, and a dual-band equalization section to shape the loudspeaker's tone at will. A double CLIP-LIMITER circuit protects the loudspeakers against distortion and power overloads. [. . . ] As soon as the music gets loud, the high frequency shuts down (passive version) The HF driver protection trips to protect the HF driver from excessive signal: turn down the volume and mid/high tone controls. As soon as the music gets loud, the level decreases (amplified version) The amplifier thermal protection trips to protect the amplifier from excessive over-heating: move the loudspeaker in a more ventilated location or turn down the volume. NOTE: The loudspeakers should never be operated at a level which causes the amplifier Clip LEDs to illuminate constantly. Different channel level Check if are using a balanced cable for one channel and an unbalanced one for the other, as this would cause a considerable difference in channel levels. [. . . ]