User manual PROGRESS DELPH842E

[. . . ] 4) You are responsible for paying all service call fees and/or transport charges and/on damages and loss incurred in connection with transportation of this appliance to and from Electrolux or its duly appointed service provider's premises. 5) Parts and appliances not supplied by Electrolux are not covered by this warranty. 6) Proof of purchase is required before you can make a claim under this warranty You may not make a claim under this warranty unless the defect claimed is due to faulty or defective parts or workmanship. Electrolux is not liable in the following situations (which are not exhaustive): A)The Appliance is damaged by: (i) use with anything other than Electrolux genuine spare parts (ii) accident (iii) vacuuming up wet materials or construction/building materials that is not normal day to day domestic dry use (iv) misuse, neglect or abuse, including failure to properly maintain or service (v) normal wear and tear (vi) power surges, electrical storm damage or incorrect power supply. [. . . ] Check if the dust container is full or if the filters are clogged. Once the cleaner has cooled down, the thermal cut-out switch resets and the cleaner will be ready for use again. 1 2 3 4 5 6 7 8 9 Combination Upholstery \ Brush nozzle. (Models Z1660/Z1661 and Z1670) Combination Crevice \ Brush nozzle Upholstery nozzle Combination floor nozzle Telescopic extension tube (Models Z1660/Z1661 and Z1670) Caddy (Models Z1660/Z1661 and Z1670) Extension tube (2 off) Handle (Manual suction control) Handle (Remote suction control Model Z1670) 10 11 12 13 14 15 16 17 18 19 Hose end Dust container release button Dust container Filter indicator HEPA filter Cage filter Cord rewind pedal On\Off Pedal switch Exhaust filter Air outlet grille IMPORTANT USER INFORMATION Dear Customer, please read through these operating instructions carefully. Above all, please observe the safety instructions on the first few pages of this booklet. Please keep these operating instructions for later reference and pass them on to any subsequent owner of this appliance. The safety standards of Electrolux electrical appliances are in keeping with the recognised rules of technology and the laws governing the safety of appliances. Prior to operating this appliance please familiarise yourself with the following safety instructions: Safety Instructions · · · · · Read all the instructions and only use the appliance for its intended purpose. The appliance must be switched off before plugging or unplugging it from the wall socket. Do not pull on the electrical cord to remove the plug from the wall socket. Always remove the plug from the wall socket before attempting any form of user maintenance or cleaning, as specified in this booklet. Do not operate the appliance with a damaged electrical cord or plug. Open the air-outlet grille by pressing down on the grille latch and pull it out. Remove the exhaust filter and replace it with a new one. Close the air-outlet grille. CLEANING AND STORING Caution: Do not immerse the cleaner, or the remote control hose handle assembly supplied with model Z1670, in water or other liquids. Do not wash the dust container in the dishwasher. Do not use abrasive materials or solvents to clean the appliance as they may damage the surface finish. Allow the appliance to cool down before cleaning. Empty the dust container and ensure that the filters are cleaned. Wipe the exterior of the appliance and the dust container with a damp cloth and then wipe it dry. On models Z1660/Z1661 and Z1670 (supplied with caddy fitted to telescopic extension tubes) the combination upholstery \ brush nozzle can be stored by attaching it to the caddy. Note: The cleaner can be stored either horizontally or in an upright position. With the hose and the extension tube attached to the combination floor nozzle, slide the parking clip of the floor nozzle onto one of the two parking positions on the cleaner. Important! [. . . ] Allow the filters to air dry throughly before replacing them in the dust container. CK LO 1. Insert the hose end into the air intake duct and push until the catch clicks into position. To remove the hose press the catch release button and pull hose end out of the intake duct. Attach the extension tube to the hose handle and the desired floor nozzle to the other end of the extension tube. [. . . ]